Оценок - 3, средний балл: 3.3
(
)
)
|
К этому устройству также есть другие инструкции:
Видеонаблюдение - VB-M600VE (10.84 mb)
Видеонаблюдение - VB-M600VE (619.05 kb)
Фрагмент инструкции
Set the maximum slow shutter time to be used when in auto exposure mode when capturing video in a dark place. Select [Disable], [1/15] or [1/8]. As longer shutter times generate residual images when capturing a moving subject, select an appropriate time according to the capture conditions. [Shutter Speed] Shutter speed can be used only if [Auto (Shutter-priority AE)] is selected in [AE Mode]. Select a desired shutter speed from the 12 levels from [1/ 8] to [1/8000]. When capturing a moving subject, selecting a higher shutter speed can reduce blurry image capture. 2 [Exposure Compensation] The exposure compensation when the camera starts can be set in the range of -3 to 3. To brighten the image, set a positive value. To darken the image, set a negative value. 3 [Metering Mode] Set the metering mode when the camera starts. [Center-Weighted] The entire screen is metered by focusing on the center of the screen. Even when slightly darker/brighter areas are present on the periphery of the screen, an appropriate exposure can be achieved for the subject near the center. Use this mode if the subject is positioned near the center of the screen. [Average] The entire screen is metered by averaging. A stable exposure can be achieved even in a capture environment where there are notable brightness differences within the screen. 5 Setting Page 5-9 Use this mode to stabilize the exposure in locations where vehicles or people are moving. [Spot] The center of the screen is metered. An appropriate exposure can be achieved for the subject at the center of the screen regardless of the brightness/darkness on the periphery of the screen. Use this mode if you want to adjust the exposure to the center of the screen because the subject is receiving a spotlight or backlight, etc. 4 [Focus Mode] Set the focus mode when camera starts. [Auto] Automatically brings the subject into focus. Normally [Auto] is selected. [Fixed at infinity] The focus can be fixed to near infinity. 5 [Smart Shade Control] Select [Disable] or one of the 7 levels from 1 (weak) to 7 (strong) for smart shade control at the camera startup. 6 [White Balance] Select the white balance according to the light source to achieve natural color in the image. [Auto] The white balance is adjusted automatically. [Manual] Set the values of red and blue gain according to the light source. Enter a value from 0 to 1023 for both the [R Gain] and [B Gain]. [Daylight Fluorescent] Select this option to capture video under daylight fluorescent lighting. [White Fluorescent] Select this option to capture video under daylight fluorescent or white fluorescent lighting. [Warm Fluorescent] Select this option to capture video under warm fluorescent lighting. [Mercury Lamp] Select this option to capture video under mercury lamps. [Sodium Lamp] Select this option to capture video under orange sodium lamps. [Halogen Lamp] Select this option to capture video under halogen bulbs or incandescent bulbs. Important • The initial camera settings 1 to 6 define the defaults that apply when the camera is started. Setting changes will be reflected only after the camera is reconnected or rebooted. Specify the settings used in the actual operating environment from the Admin Viewer (P. 7-12). • If the subject is a traffic signal or electronic scoreboard, etc., the captured image may flicker. In this case, try changing the [AE mode] setting to [Auto (Shutter-priority AE)] and selecting a shutter speed lower than 1/100 to see if the problem improves. • In conditions where an outdoor scene is captured from an indoor location through a glass window, the camera may focus on the glass surface if there is dust or water there. Install the camera at the shortest possible distance (within 30 cm) from the glass surface. Note • See “Subjects Difficult to Focus On” (P. 3-8). • Focus ranges (rough guide) are shown in the following table according to the settings of [Day/Night] (P. 5-11), etc. Focus Mode Dome Setting Day/Night Setting Day Mode Night Mode Wide end Tele endWide end Tele end Auto Do not use .0.3 m (12 in) . 1.0 m (3.3 ft) . 1.0 m (3.3 ft) . 1.5 m (4.9 ft) - Use .2.0 m (6.6 ft) . 1.0 m (3.3 ft) -.2.2 m (7.2 ft) - Fixed at infinity Do not use/Use Point of infinity* * When using an infrared lamp, the camera may be out of focus. Camera Control 1 [Digital Zoom] Set digital zoom to [Enable] or [Disable]. * The higher the digital zoom ratio, the lower the image quality becomes. 2 [Image Stabilizer] Select [Disable], [On1] or [On2] for image stabilizer. Image stabilizer has the effect of correcting blurry images. Try [On2] if the image is still blurry after selecting [On1]. If you have selected [On1] or [On2] as the image stabilizer setting, the viewing angle will be smaller and the image more coarse than when [Disable] is selected. This is not a malfunction. Degree of blurriness corrected Degree of blurriness corrected Effective pixels Disable — 100% Approx. 1.23 megapixels On1 Small 83% Approx. 0.85 megapixels On2 L...
Эта инструкция также подходит к моделям:Видеонаблюдение - VB-M40 (10.28 mb)
Видеонаблюдение - VB-M600D (10.28 mb)
Видеонаблюдение - VB-M700F (10.28 mb)