Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
FLOOR 1 Character Cursor Character Area Command Editing Area Pointer Highlighted 4. To specify the ID display position: 1. Select "POSI" and press the [SET] button. > The entered camera ID will be highlighted on the screen. 2. Move it into the appropriate position and press the [SET] button. > The position is determined and the screen will return to the "CAMERA ID" menu. Note: • Keep pressing any of [LEFT], [RIGHT], [UP], or [DOWN] button for a second or more to move the camera ID faster as necessary. 2. Light Control Mode Setting (ALC) Select a light control mode depending on the lens type mounted. ALCv: Is applicable to the auto iris lens. "SUPER-D3" is available with this selection. 2-1. ALC Mode with SUPER-D3 ON Super Dynamic 3 Function (SUPER-D3) In the SUPER-D3 mode, more photometric weight is given to the center of the screen than to the edge where a bright backlight would most likely be located. SUPER-D3 ON SUPER-D3 OFF Nighttime Daytime Nighttime Daytime SUPER-D3 ON: Enables SUPER-D3 to compensate backlight automatically. SUPER-D3 OFF: Enables manual setting to compensate backlight. Notes: • When set to "ON", the available parameters for "SHUTTER" and "SENS-UP" will be limited as shown on the next page. • Set "SUPER-D3" to "OFF" when noise in a bright portion, flickerings, or color deterioration are observed. 1. Move the cursor to "ALC" and press the [SET] button. **ALC CONT** > The "ALC CONT" menu opens. BACK LIGHT COMP 2. Select "ON" for "SUPER-D3". SUPER-D3 ON 3. Adjust the video output level (LEVEL) by moving the "I" cursor. It may be better to adjust "LEVEL" slightly higher. LEVEL ...I...128 -+ RET TOP END 2-2. ALC Mode with SUPER-D3 OFF 1. Move the cursor to "ALC" on the "CAMERA SETUP" menu and select "OFF" for "SUPER-D3" on the "ALC CONT" menu. > "MASK SETv" appears on the "ALC CONT" menu. 2. Select "MASK SET" and press the [SET] button. > The 48 mask areas appear overlaid on the camera picture with the blinking cursor in the upper left corner. **ALC CONT** BACK LIGHT COMP SUPER-D3 OFF MASK SET LEVEL ...I...128 -+ RET TOP END 3. Move the cursor to an area where the backlight is bright and Blinking press the [SET] button to mask the area. > The masked area appears alternately white and blinking when the cursor is on the area, or it turns white when the cursor is on other areas. 4. To cancel masking, move the cursor to a masked area and press the [SET] button. > When masking of the area is cancelled, it changes from white to normal. White To cancel all the masking, press the [LEFT] and [RIGHT] Blinking buttons simultaneously for 2 seconds or more. 5. Repeat step 3 and 4 as necessary. 6. Press the [SET] button for 2 seconds or more. > The "ALC CONT" menu appears. 7. Adjust the video output level (LEVEL) by moving "I" cursor. Note: • If "ON" is selected for "SUPER-D3", a shadow (black line) may appear at the boundary between the bright and the dim portions. This is a natural phenomenon and does not indicate trouble. 3. Shutter Speed Setting (SHUTTER) Select a proper shutter speed when "ALC" is selected on the "CAMERA SETUP" menu. Selecting a faster speed will reduce blurring when objects quickly move. The default setting is "OFF". OFF (1/60) 1/100 1/250 1/500 SUPER-D3 OFF: 1/10000 1/4000 1/2000 1/1000 Notes: • Only "OFF" is available when "SUPER-D3" is set to "ON". • When a faster speed is selected for the electronic shutter, the picture will generally become darker, and sometimes a smear (vertical stripes caused by bright objects) may appear. 4. Gain Control Setting (AGC) Select an automatic gain control mode. This setting raises the gain and brightens the image under low light conditions. The default setting is "ON (HIGH)". Available modes: ON (HIGH), ON (MID), ON (LOW), OFF 5. Electronic Sensitivity Enhancement (SENS UP) Select a proper enhancement rate when the camera is set to ALC mode. The higher rate you select, the brighter the picture will be. The default setting is "OFF". AUTO: Sets "AGC" to "ON" and adaptively raises the sensitivity up to the selected amplification rate, for example 10 times when set to "X10 AUTO". FIX: Raises the sensitivity fixedly to the selected rate. OFF: Does not raise the sensitivity. OFF X2 AUTO X4 AUTO X6 AUTO X10 AUTO OFF SUPER-D3 OFF: X32 FIX X16 FIX X10 FIX X6 FIX X4 FIX X2 FIX X2 AUTOOFF* X4 AUTO X6 AUTO X10 AUTOSUPER-D3 ON: * Default Notes: • Some types of system controllers may not operate some of the SENS UP functions. If this happens, use the operation buttons on the camera. • When you select "AUTO" for "SENS UP" and "ON" for "SUPER-D3", the SENS UP function has priority so that the SUPER-D3 function is not activated automatically. • While the SENS UP function is selected, noise, spots or a whitish phenomenon may appear in the picture when the sensitivity of the camera is increased. This is a normal phenomenon. • Only when "OFF", "X2 FIX", or "X2 AUTO" is selected for sensitivity enhancement (SENS UP), it is possible to perform ABF adjustment or to se...