Caution: To prevent fire or electric shock hazard, a UL listed wire (VW-1, style 1007) should be used for DC 12V or AC 24V Input Terminals. -3 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS WV-BP330 VIDEO OUTGEN-LOCK L INT AGC ON ALC BLC ON VIDEO G/L 75 VIDEO LEVEL V. PHASE H . LL OFF ELC OFF DC Hi-Z GND AC 24V IN 1 2 VIDEO OUTGEN-LOCK L INT AGC ON ALC BLC ON VIDEO G/L 75 VIDEO LEVEL V. PHASE H . LL OFF ELC OFF DC Hi-Z DC 12V IN VIDEO OUTGEN-LOCK L AGC ON ALC BLC ON VIDEO G/L 75 VIDEO LEVEL H . OFF ELC OFF DC Hi-Z -4 q Auto Iris lens Connector This connector is for connecting the auto iris lens by a 4-pin male connector supplied as a standard accessory (Part No. YFE4191J100). w Flange-back Adjusting Ring This ring adjusts the back focal length or picture focus. Rotate this ring clockwise for a C-mount lens or counterclockwise for a CS-mount lens. e Lens (option) r Camera Mounting Screw Hole This hole for mounting the camera onto a mounting bracket. t Power Cord (only WV-BP330) Connect this power cord to an electrical outlet of 120V AC 60Hz. y DC 12 V Input Terminal (DC 12V IN (only WV-BP332)) This terminal is for connecting the 12V DC power supply cord. u AC 24V Input Terminal (AC 24V IN (only WV-BP334)) This terminal is for connecting the 24V AC 60Hz power supply cord. i Synchronization Mode Selector (INT, LL (only WV-BP330 and WV-BP334)) Selects the camera synchronization mode from internal sync mode (INT) or line-lock mode (LL). INT: When no signal is supplied to the GEN-LOCK connector, the camera synchronization mode is set to internal 2:1 interlace. Whenever the gen-lock video signal is supplied to the GENLOCK connector, the camera synchronization mode is automatically set to external synchronization. LL: The camera synchronization mode is set to line-lock even if the gen-lock video signal is supplied to the GEN-LOCK connector. Note: Set this selector to INT for gen-lock operation. o AGC ON/OFF Selector (AGC ON, OFF) Selects the gain of the video amplifier as follows: AGC ON: When the lens iris is fully open under low light conditions, a clear picture is obtained by automatic increase of the gain. OFF: A natural and low-noise picture is obtained under low light conditions. -5 !0 Automatic Light Control / Electronic Light Control Selector (ALC , ELC) Automatic Light Control / Electronic Light Control Selector (ALC , ELC) Lets you select the mode according to the lens type that is used with this camera. ALC: Select this mode when an auto iris lens (ALC lens) is used with this camera. ELC: Select this mode when a fixed iris lens or manual iris lens is used with this camera. !1 Back Light Compensation Mode Selector (BLC ON, OFF) Lets you select the mode according to the position of the object and light conditions on the screen. BLC ON: More photometric weight is given to the center of the screen than to the edge of the screen. Select this mode if the background light is strong such as a spotlight. OFF: Select this mode if the main object is not located in the center of the screen and a source of bright light is located near the center of the screen. !2 Lens Drive Signal Selector (VIDEO, DC) Lets you select the mode according to the type of auto iris lens drive signal to be supplied to the lens from the auto iris lens connector. VIDEO: Select this mode if you are using the auto iris lens that requires a video drive signal. DC: Select this mode if you are using the auto iris lens that requires a DC drive signal. !3 Gen-lock Termination Selector (Hi-Z, G/L75.) Set this selector to Hi-Z when a gen-lock video input signal is looped through. In all other cases, set this selector to 75.. !4 Vertical Phase Control (V. PHASE (only WV-BP330 and WV-BP334)) Allows you to adjust the vertical phase of the camera signal to match the vertical phase of the line powers. !5 Video Level Control (VIDEO LEVEL, H(High)L( Low)) Allows you to adjust the video level when the Lens Drive Signal Selector is set to DC and the auto iris lens requiring the DC drive signal is mounted on the camera. Note: The video level should be adjusted by the lens when the auto iris lens requiring the video drive signal is mounted on the camera. !6 Video Output Connector (VIDEO OUT) This connector is for connecting with the VIDEO IN connector of the monitor. -6 !7 Gen-lock Input Connector (GEN-LOCK) This connector is for connecting an external system for synchronization. Gen-lock Input Connector (GEN-LOCK) This connector is for connecting an external system for synchronization. Cautions: 1. Connect to 12V DC (10.5V-16V) or 24V AC (19.5V-28V) class 2 power supply only. Make sure to connect the grounding lead to the GND terminal when the power is supplied from a 24V AC power source. 2. To prevent fire or electric shock hazard, use a UL listed wire VW-1, style 1007 cable for the Input Terminal. -7 CONNECTIONS CONNECTIONS A. WV-BP330 (120V AC 60Hz) Connect the power cord to an elec...
)
