Оценок - , средний балл:
(
)
)
Производитель: Panasonic
Размер: 378.16 kb
Название файла: WJPB85R08.PDF
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
Otherwise components on the board may be damaged by stat c electricity. ■ Preface The WJ-PB85R08 RS485 Data Board is an optional board for exchange of control cata between the Camera Control Cage (MXCONT) and the camera site. ■ Appearance 0 Data Connectors (TA/TB/RA/RB/G 1-8) These connectors are used to exchange contro< data between the camera site equipment. For connection, use a data grade shielded 4-wire twisted pair cable suitable for RS-485 communication. TXD RXD Rt: Termination Resistor SVV: Selection Switch, -ull Duplex; Hail Duplex GND: Ground Connected to each channel and common ground. © ■© ■ Board Setting Before installing this board, the following settings should be made by qualified service personnel or system installers. 1. Set switches (SW1 and SW2) on the board to designate the RS-485 Data board number as shown in the following table. The factory default setting is Board Number 1 (00), Board No. Data I/O SW Positions SW2 SW1 1 1 -8 0 0 2 9- 16 0 1 3 17-24 0 2 4 25-32 0 3 5 33-40 0 4 6 41 - 48 0 5 7 49 * 56 0 6 8 57-64 0 7 9 65 - 72 0 8 10 73 - 80 0 9 11 81 - 88 0 A 12 89-96 0 B 13 97 - 104 0 C 14 105- 112 0 D 15 113 - 120 0 E 16 121 - 128 0 F -2- 2. Set switches (SW101. SW201, SW301. SW401. SW501, SW601, SW701. and SW801) on the board to choose either data termination ON or OFF as shown below. The factory default settings are TERM ON. TERM ON □ TERM OFF Installation The following installation should be made by qualified service personnel or system installers. • Installing Additional Extension Boards 1. Remove the screws from the rear panel(s) of the WJ-SX850 Matrix Switcher Card Cage. Set switches {SW102, SW202, SW302, SW402. SW502, SW602, SW702, and SW802) on the board to choose either Full Duplex (4 LINE) or Half Duplex (2 LINE) communication lines as shown below. The factory default settings are Full Duplex (4 LINE). 4LINE II 2LINE 4. Confirm that switches (SW3) on the board are set to the OFF position as shown below. DIP ON OFF 1 One way mode Handshake mode 2 No retry mode 3 retries mode 3 Reserved Reserved 4 Reserved Reserved 2. Remove the rear panel(s). 3. Remove the front panel of the cage by removing the two screws on the panel shown below. -3- 4. Place the Boards into the specified positions in the front or rear of the Cage by sliding them along the board guides as shown below. 5. Make sure to push in the Boards until they are seated firmly. 6. Secure the rear board by tightening the two screws on the board. 7. Close open spaces on the rear of the Cage with the supplied rear panel(s). 8. Close the front of the cage by fixing the front panel. Specifications Data Input/Output (1 - 8): Transmission Speed (Baud Rate): Dimensions: Weight: RS-485 [5-pin T(A), T(B), R(A), R(B), G] x8 Full Duplex or Half Duplex selectable 1 200- 19 200 bps Front Board; Rear Board; 0.5 kg (1.1 lbs) 255(W)x 250(H) X 12(D) mm 10-1/16"(W) X 9-l3/16"(H) X 1/2"(D) 117.5(W) X 265(H) X 20(D) mm 4-5/8"(W) X 10-7/16"(H) X 13/16"(D) Weight and dimensions indicated are approximate. Specifications are subject to change without notice. Panasonic Security and Digital Imaging Company A Division of Matsushita Electric Corporation of America Executive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094 Regional Offices: Northeast: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303 Southern: 1225 Northbrook Parkway, Suite 1-160, Suwanee, G A 30024 (770) 338-6838 Midwest: 1707 North Randall Road, Elgin, IL 60123 (847) 466-5211 Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-7840 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada (905)624-5010 Panasonic Sales Company Division of Matsushita Electric of Puerto Rico Inc. Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 (809)750-4300 © Matsushita Communication Industrial Co., Ltd. 1999 NM1099-0 VWV80A5055AN Printed in Japan