Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Then fix it with two of the fixing screws in step 3. Torque: 0.49 N»m (5 kgf»cm) Note: To install one HDD, place it into bay #1. 9. Pluq the two harness connectors into the installed HDD. Jumper connector 10. Repeat the above steps for HDD #2. 11. Replace the HDD lid. 12. Set the Hard Disk Detection switch to INSTALLED. ■ Connection and Switch Setting The figures show examples of SCSI connections. The WJ-HD500 Digital Disk Recorder controls the DVD Extension Unit through the SCSI chain. «¿Connection between the WJ-HD500 and a WJ-HDE510 without HDD> The figure shows a WJ-HDE510 without an HDD. The DVD-RAM is used for backup of the data recorded on the WJ-HD500 Digital Disk Recorder. 1. Connect between the COPY port on the WJ-HD500 and the COPY IN port on the 1st DVD Extension Unit with the supplied (WJ-HDE510) SCSI cable. 2. Connect between the EXT STORAGE port on the WJ-HD500 and the EXT IN port on the 2nd Extension Unit with the supplied (WJ-HDE500) SCSI cable. The system can be expanded by up to 6 Extension Units. To connect the other Extension Units, refer to the operating instructions of each unit for further information. EXT STORAGE Digital Disk Recorder WJ-HD500 SCSI ID=6 and 7 COPY port Extension Unit #2 WJ-HDE500/HDE505 SCSI ID=0 to 5 -7- Error Connection Connect each of the error outputs to the CONTROL port on the rear panel of the WJ-HD500 as shown below. The WJ-HD500 will display a thermal error on the monitor screen. WJ-HD500 CONTROL Port 13 1211109 8 7 •09999900000« 9 0 0 0 9 0 20 Extension Unit #3 Error Out Extension Unit #4 Extension Unit #5 Error Out G Extension Unit #6 Error Out ►— =3 DVD Extension Unit #1 o ao Error Out G Terminal board on the Extension Unit O oc ac LU Extension Unit #2 < IS or LU uz t— Error Out G O ON CM O O Error Out Strip G 6 mm _JJ To CONTROL port on the Digital Disk Recorder WJ-HD500 Switch Settings 1. Set MODE switch #2 on the rear of the WJ-HD500 to 1234 OFF when connecting a DVD Extension Unit without I an optional HDD. ON Set the MODE switch to ON If the other Extension MODE Units are installed in the system. 2. Set the SCSI ID and TERMINATION of the Extension Units as required. «¿Connection between the WJ-HD500 and a WJ-HDE510 with HDD> The figure shows the WJ-HDE510 with an HDD. The DVD-RAM is used for backup the data recorded on the WJ-HD500 Digital Disk Recorder as well as for storing the data of the extension hard disk drive units in the system. 1; Connect between the COPY port on the WJ-HD500 and the COPY IN port on the 1st DVD Extension Unit with the supplied (WJ-HDE510) SCSI cable. 2. Connect between the EXT STORAGE port on the WJ-HD500 and the EXT IN port on the 2nd Extension Unit with the supplied (WJ-HDE500) SCSI cable. Repeat the connection steps for any subsequent extension units, The system can be expanded by up to 6 Extension Units. To connect the other Extension Units, refer to the operating instructions of each unit for further information. EXT STORAGE Digital Disk Recorder WJ-HD500 SCSI ID=6 and 7 COPY port =}_f= Д'0,<ва1 • “ i COPY EXT IN Y IN j. =s=T-▼= * QÄ.* 4 Ш» - SCSI cable (supplied) DVD Extension Unit #1 WJ-HDE510 SCSI ID=0 to 5 Extension Unit #2 WJ-HDE500/HDE505 SCSI ID=0 to 5 Error Output Connection Connect each of the error outputs to the CONTROL port on the rear panel of the WJ-HD500 as shown below. The WJ-HD500 will display a thermal error warning on the monitor screen. WJ-HD500 CONTROL Port 13 1211109 8 7 20 DVD Extension Unit #1 Error Out G Extension Unit #2 Error Out G Extension Unit #3 Error Out Extension Unit #5 Error Out Extension Unit #6 Error Out Terminal board on the Extension Unit To CONTROL port on the Digital Disk Recorder WJ-HD500 —ZÆ z: i— о ос СП LU _1 S СП LU о CD _I_ 1— Z О О о Error Out Strip Г G 6 mm 1 1 -9- Switch Settings 1. Set MODE switch #2 on the rear of the WJ-HD500 to ON when connecting a DVD Extension Unit with an optional HDD. 2. Set the SCSI ID tor the DVD Extension Unit and each subsequent Extension Unit with the - or + selector on the rear of each Unit. 0 to 5: IDs for Extension Units. Note: SCSI ID 6 and 7 are reserved for WJ-HD500 Digital Disk Recorder. 3. Set the termination switch to ON for the Extension Unit located at the end of the SCSI chain. 1234 I X V * Ml ON MODE SCSI ID □ 0 + □ TERMINATION □ ON OFF Mounting into a Rack The installation described below should be made by qualified service personnel or system installers. The DVD Extension Unit can be mounted into the rack as described below. 1. Remove the four rubber feet by removing the four screws from the bottom of the DVD Extension Unit. 2. Place the rack mounting brackets on both sides of the DVD Extension Unit and tighten with the four supplied screws (M4x10). Remove 4 M3X10 (Supplied) 3. Install the DVD Extension Unit with the rack mounting brackets in the rack, securing it ...