Оценок - 4, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
The number of days specified by this setting stand for the number of days the records will be protected from the present, while the records older than that will be erased. SYSTEM SETUP (2 OF 2) PLAY PRIORITY LOCAL TIME ADJUST SETUPO AUTO ERASING OFF 1. Move the cursor to AUTO ERASING with the [D] or [C] button. 2. Select the desired number of days with the JogDial, and press the JogDial. OFF: Auto erasing is not applied. 1 DAY: Only today’s records from 00:00 onward are protected. Records before 24:00 yesterday are erased. 2 to 10DAYS: Records before the specified number of days are erased. 14, 30, 45, 60, 90, 120, 150, 180DAYS: Same as above. Notes: • The number of days include today as 1 day, therefore 2DAYS covers today and yesterday. • Auto erasing is implemented at 24:00 midnight. Playback will stop once when the time reaches 24:00, then will restart with a different portion based on the renewed day count. Alarm Setup (ALARM SETUP) The digital disk recorder accepts alarm signals supplied from connected devices such as sensors or camera site equipment. The recorder itself also generates an alarm signal when the preset motion detection is activated. Any alarm signal starts recording with the preset recording mode, field rate, and picture quality specified in the REC MODE menu described earlier. Alarm recording stops when the preset time has elapsed, the alarm [RESET] button on the front panel is pressed, or the ALARM RESET IN signal is supplied from the connected device. The recorder outputs an alarm recovery signal from the rear panel. ALARM SETUP ALARM BUZZ ON VIDEO LOSS ON MONITOR MODE SPOT VMD SETUPO Alarm Buzzer (ALARM BUZZ) Enables or disables buzzer beeping when an alarm operates. 1. Move the cursor to ALARM BUZZ with the [D] or [C] button. 2. Rotate the JogDial to select ON or OFF. The default is ON. ON: Buzzer beeps while alarm is active. OFF: Buzzer does not beep. Video Loss (VIDEO LOSS) Enables or disables video loss detection. 1. Move the cursor to VIDEO LOSS with the [D] or [C] button. 2. Rotate the JogDial to select ON or OFF. The default is ON. ON: Enables the recorder to detect video loss. OFF: Ignores video loss. Monitor Mode (MONITOR MODE) This setting specifies whether to allow the display to change from the currently displayed picture to the alarmed channel when an alarm operates. 1. Move the cursor to MONITOR MODE with the [D] or [C] button. 2. Select the parameter with the JogDial, and press the JogDial. The default is SPOT. SPOT: Switches to the picture of the alarmed channel. OFF: Retains the previous display mode. Video Motion Detection (VMD SETUP) A VMD or Video Motion Detector senses changes in the video signals within a preset area and supplies alarm output. When a change is detected, the recorder starts recording. The detection sensitivity and area are selected on this menu. 1. Move the cursor to VMD SETUPO with the [D] or [C] button, and press the JogDial. The VMD SETUP window opens. VMD SETUP CAM SENS 1 OFF 2 LOWO 3 MIDO 4 HIGHO 5 OFF 6 OFF 7 OFF 8 OFF 2. Move the cursor to the desired line. 3. Rotate the JogDial to select the desired parameter, and press the JogDial. The default is OFF. LOW: Low sensitivity MID: Medium sensitivity HIGH: High sensitivity OFF: Motion detection is disabled. The area setup window appears with an asterisk when other than OFF is selected. The asterisk represents the upper-left or bottom-right of the detection area. The division lines are not actually displayed on the monitor. * CAM1 * CAM1 Notes: • VMD should be used when the input to the unit is from an ordinary camera. Select [OFF] to avoid useless VMD when a video multiplexer or combination camera supplies the input to the unit. • Set ALARM SUSPEND to ON when you do not want VMD to be activated during the VMD setup. • There may be cases where VMD does not sufficiently detect changes, since it detects the changes in luminance. • The detection area may include areas slightly outside the border. • The buzzer will beep if detection takes place during the area setup. 4. Set the upper-left end of the detection area. Move the asterisk to the right or left with the JogDial, and up or down by pressing the [D] or [C] button. PUSH • PAUSE / / SET REW/FF / STEP / 5. Press the JogDial to enter the upper-left end of the detection area. The asterisk position is highlighted. 6. Set the bottom-right end of the detection area similar to steps 3 and 4 above. 7. Press the JogDial. The area is highlighted. Up to 4 areas can be selected. These may partially overlap. Repeat steps 3 to 6 to select more areas. To deselect an area, move the cursor to the upper-left end of the area, and press the JogDial. q w e r Communication Setup (COMMUNICATION SETUP) Communication parameters are set to match those of the connected devices and the system configuration. The serial port setup and network setup are made. COMMUNICATION SETUP SERIAL PORT SETUPO NETWORK SETUPO Serial Port Setup (SERIAL PORT SETUP) The SERIAL PORT S...