Инструкция по эксплуатации Panasonic, модель GPUS932CUS
Производитель: Panasonic
Размер: 221.87 kb
Название файла: GPUS932CU.PDF
Язык инструкции:
Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста
Фрагмент инструкции
• Selection of setting item: Press the [g] button or the [h] button to move the cursor. • Change of settings: Press the [e] button or the [f] button. • Display of advanced setup screen: Press the [SEL] button when "*" is attached to the target setting item. • Return to previous setup screen: Move the cursor to "RET" and press the [SEL] button. v To return to the camera image screen after storing the settings, move the cursor to "END" and press the [SEL] button. The settings can be stored even if the power of the CCU is turned off. 1. Camera title setting [CAMERA ID] This item specifies the camera title. The camera title that indicates the camera location and other information about the camera is created with alphanumeric, symbol, and katakana characters and displayed on the screen. The camera title is named with up to 16 characters. Follow the procedure below to specify the camera title. Top screen of SETUP menu ** SET UP ** P1 CAMERA ID *OFF ELC *OFF SHUTTER OFF GAIN OFF SENS UP OFF OUTPUT SEL RGB(NOR) END Title creation screen ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789 ().,'":;&#!?= +-*/%$AUO.NA < > SPACE *POSI RET END RESET ................ Editing area Display positioning screen FLOOR 1 z Set "CAMERA ID" to "ON" and press the [SEL] button. > The title creation screen appears. Note: • Even if "CAMERA ID" is set to "OFF", pressing the [SEL] button calls up the title creation screen. Important: • When "CAMERA ID" is set to "OFF", the camera title does not appear even if the title is specified. x Move the cursor to the target item with use of the [g], [h], [e], and [f] buttons and press the [SEL] button. > The entered characters are displayed in the entry range. • To revise the character, move the cursor to "<" or ">" and press the [SEL] button. Move the cursor to the character to be revised in the entry range and enter a character newly. • To enter a blank, move the cursor to "SPACE" and press the [SEL] button. • To delete all the entered characters, move the cursor to "RESET" and press the [SEL] button. c Move the cursor to "POSI" and press the [SEL] button after title entry. > The display positioning screen appears to show the entered camera title blinking. v Position the title with use of the [g], [h], [e], and [f] buttons and hold down the [MENU] button for more than 2 seconds. > The title position is decided and the title creation screen appears again. 2. ELC setting [ELC] Setting ELC (electronic light control) to ON provides automatic adjustment of the screen brightness. The convergence level of ELC can be specified at “BRIGHTNESS” in the SEL menu ( page 25). If a photographic subject has a bright light such as a spotlight in its backgroud, the subject may appear shadowy. To eliminate this phenomenon, mask the bright area in the background to perform correction. Top screen of SETUP menu ** SET UP ** P1 CAMERA ID *OFF ELC *OFF SHUTTER OFF GAIN OFF SENS UP OFF OUTPUT SEL RGB(NOR) END "ELC CONT" screen ** ELC CONT ** AREA ALL PEAK/AVE P....|....A RET END z Set "ELC" to "ON" and press the [SEL] button. > The "ELC CONT" screen appears. x Move the cursor to "AREA" and use the [e] and [f] buttons to select an area. The area is selectable from the types shown below. > The detection areas shown as follows are not displayed. ALL (default): All of the areas on the screen are the detection area. S CIRCLE: The small circle in the center of the screen is the detection area. M CIRCLE: The medium circle in the center of the screen is the detection area. L CIRCLE: The large circle in the center of the screen is the detection area. MANU: The detection area can be manually specified. ( page 18) AUTO: The dark areas are automatically covered and only the bright areas are automatically detected. c Move the cursor to "PEAK/AVE" and use the [e] and [f] buttons to adjust the detection level. When the cursor is moved to "P", the peak value (maximum) is detected. When the cursor is moved to "A", the average value is detected. Manual setup of detection area The detection area is manually specified. "ELC CONT" screen ** ELC CONT ** AREA ALL PEAK/AVE P....|....A RET END Mask setting screen z Select "MANU" for "AREA" on the "ELC CONT" screen and press the [SEL] button. > The mask setting screen appears. x Use the [g], [h], [e], and [f] buttons to select an area to be masked and press the [SEL] button. > The selected area is displayed white. Note: • To cancel the specified area, move the cursor to the target area and press the [SEL] button. To cancel all the masks, hold down the [e] and [f] buttons simultaneously for more than 2 seconds. c Hold down the [MENU] button for more than 2 seconds after area setting. > The "ELC CONT" screen appears again. 3. Electronic shutter setting [SHUTTER] The electronic shutter speed is specified. The speed is selectable from the following. OFF (default),1/100 (1/120*), 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000, and MANU Select "MANU", and press [SEL] button. The "SHUTTER" screen ...
)
