Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
Press {TALK} while speaking to the caller and release the button to allow the caller to speak to you (page 24). Note: L If the door station is installed in a noisy environment, {PUSH} mode or {AUTO} mode may not function properly. Using the Unit {PUSH} mode (Push to talk mode) 1 When a call is received from the door station, press {TALK}. 2 Speak to the visitor. 3 To end the conversation, press {TALK}. L The display will turn off. {AUTO} mode (Auto talk mode) This mode allows you to answer the call by voice. Speak a brief reply into (or toward) the monitor station, such as “Yes?” or “Hello?”. This reply is used to start {AUTO} mode; the visitor will not hear your reply. The monitor station will beep to indicate {AUTO} mode has started and you may then speak to the visitor. 1 When a call is received from the door station, answer “Yes?” within 30 seconds. L A beep will sound to indicate that you can talk to the visitor (hands-free conversation). 2 Speak to the visitor. 3 To end the conversation, press {TALK}. Note: L Make sure you are within about 50 cm (20 inches) of the monitor station. L You can also answer the call by pressing {TALK}. L Your initial reply should be brief (less than 1 second), otherwise {AUTO} mode will not start. L If a visitor calls you, a loud, brief sound (such as a barking dog) may start {AUTO} mode even though you have not replied by voice. {HOLD} mode (Hold to talk mode) 1 When a call is received from the door station, press and hold {TALK} to speak to the caller. L A beep will sound and the Talk indicator will light. 2 To listen to the visitor, release {TALK}. L The Talk indicator will turn off. 3 To speak again, press and hold {TALK}. 4 To end the conversation, tap {TALK}. Note: L Make sure you speak to the caller only while pressing {TALK} and release {TALK} when you have stopped speaking so that the caller can speak to you. Using the Unit Note: L Speak clearly about 50 cm (20 inches) away from the microphone. L While the display is on, you can press {BRIGHT} repeatedly to select the desired brightness. If a power failure occurs, the brightness setting will be reset. L If you do not answer a door call within 30 seconds, the display will turn off. If you press {TALK} again, the display will turn on again, and you can talk to the visitor. L The conversation will be automatically disconnected in about 1 minute and 30 seconds (about 1 minute in {HOLD} mode). To resume the conversation, press {TALK}. L At night or when there is not enough lighting in the doorway, the display will be shown in black and white. Using the Unit Monitoring the outside You can monitor the sound and camera image from the door station for up to 1 minute at a time. {TALK} {MONITOR} {BRIGHT} 1 Press {MONITOR}. L The outside image will be shown on the display, and the outside sound will be heard. The inside sound will not be heard at the door station. L If necessary, press {BRIGHT} repeatedly to select the desired brightness. 2 To end monitoring, press {MONITOR}. L Even if you do not press {MONITOR}, monitoring will automatically end in about 1 minute. Note: L While you are monitoring, calls from the door station will not be heard. L To talk to the visitor while monitoring, press {TALK}. Using the Unit Opening a door (door opener) You can open the door using the monitor station (a separate door opener is required). {DOOR} 1 While the display is on, press and hold {DOOR}. L The door will remain open while {DOOR} is pressed. Note: L See page 11 for wiring information. Help Troubleshooting Problem Cause and solution The display is not clear or is blurry. LThe surface of the door station is dirty. Clean it with a soft dry cloth. LThe surface of the door station is wet with dew. Wait for the condensation to evaporate. LChange the brightness of the display by pressing {BRIGHT}. The display is white, or black or white lines are shown on the display. LStrong light such as sunlight is shining into the camera of the door station. Though this may cause the display image to become difficult to see, it is not a malfunction. The color of the display is different from the actual color. LCertain types of lighting (dusk, incandescent lighting, etc.) may be shining into the camera. We recommend lighting the area of the door station with white, fluorescent light. The display will not display anything or no voices can be heard. LThe power cord is not connected. Check the connections. LContact our service personnel. The monitor station does not ring. LThe ringer volume is turned off. Turn it on. LThe power cord is not connected. Check the connections. LContact our service personnel. I cannot talk to the visitor or the ringer tone rings regularly. LPress and hold {BRIGHT} for about 10 seconds until a beep sounds. Wait for another 10 seconds and try again. LContact our service personnel. Sound cuts in/out or fades. LThe surroundings of the monitor station or the door station are noisy. If you are using {PUSH} mode or {AUTO}mode, your c...