Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
6 Parts and their function Parts and their function . Rotary head This rotates in the horizontal direction. . Pedestal . POWER ON/OFF switch Where a switch is pushed in, the unit’s power is turned on, and the unit’s power is turned off after the switch has jumped out. . AC inlet [AC IN] (AC 3-point inlet) Connect the accessory AC power cable to this inlet. . Camera mounting base mounting screws M5. mm hexagon socket head screws (with flat washers, spring washers) ( of each provided as accessories) These parts are used to secure the camera mounting base to the rotary arm. . Tally lamp (accessory) This is lighted up red by the selected signals. . Rotary arm mounting screws M5. mm hexagon socket head screws (with flat washers, spring washers) (4 of each provided as accessories) These parts are used to secure the rotary arm to the rotary head. . Rotary arm This rotates in the vertical direction. . Camera mounting base Mount the convertible camera or multi-purpose camera on this base. . Pan-tilt head mounting holes These four holes are used when installing the pan-tilt head. . Bottom panel Use the unit with this panel in position. . PROMPTER connector The prompter is connected to this connector. The maximum current which can be supplied from the DC 1 V OUT socket is .5 A. When the prompter is connected, the pan-tilt head’s speed is reduced to about one-third. When connecting the prompter, be absolutely sure to short-circuit the DETECT terminal (Pin No.14) and the GND terminal (Pin No.15). Note . Consult your dealer when a prompter is to be installed since it will be necessary for the balance between the mounting fixture and overall weight and other aspects to be checked. Pin layout as seen facing the prompter connector Pin No. 1 9 10 11 4 1 5 1 6 14 7 15 8 Signal Name – – – – – – PROMPTER VIDEO PROMPTER VIDEO GND – – – – – – DC 1 V OUT – – – GND – – – – – – DETECT – – – GND – – – . Guide pin Use this to determine the direction in which the camera is to be mounted. . Camera mounting screws (U1/4” 20UNC) These are used to secure the camera firmly after it has been mounted. . Side blank panel For normal operation, use the unit with this panel in position. 8 Parts and their function Rotary head connector panel . ND/EXT connector [ND/EXT] This is for the control of the ND filter and lens extender of the motorized lens unit. Connect this connector when using a motorized lens unit with ND filter and lens extender functions. The cable described in “Cable specifications” on page 6 is required in order to connect this connector. CanonEXT (.) CVCC (12 V) CanonEXT (.) CGND ND Signal EXT Return ND Return EXT Signal (Pin layout as seen from cable end) The current rating of the CVCC and CGND pins is 500 mA (max). Any devices whose maximum current consumption exceeds 500 mA cannot beused. . LENS I/F (2) connector [LENS I/F (2)] This is used when an IAS, WAS or VAS lens made by Canon or an RD lens made by Fujinon is to be used. The optional connecting cable is required to connect the lens with the connector. The current rating of LENS I/F ( ) connector is 500 mA (max). The lens whose maximum current consumption exceeds 500 mA cannot be used. Concerning the maximum current consumption of the lens, contact the lens manufacturer. Lens Cable Canon Digital AW-CA4DLZG Analog AW-CA4ALZG Fujinon AW-CA4FLZG Note . Refer to the instructions for using the connecting cable to ensure that it is connected properly. . LENS P/S ON/OFF switch [LENS P/S] When this is set to ON, power is supplied to the lens from the LENS I/F (1) connector. When it is set to OFF, power is no longer supplied to the lens from the LENS I/F (1) connector. Set this switch to OFF when power is to be supplied from a source outside the unit without using the AW-PH405’s dedicated camera cable. . LENS I/F (1) connector [LENS I/F (1)] This is used to control the zooming and focusing of the motorized lens unit. Use the motorized lens unit’s remote (zoom/focus) control cable to make the connection. . CAMERA I/F connector [CAMERA I/F] This is used for the control of the convertible camera. Use the camera cable supplied with the AW-PH405 to connect the connector with the REMOTE connector on the camera. Depending on the functions of the optional card, a special camera cable (sold separately) is required. . SDI IN connector [SDI IN] Use a coaxial cable to connect this to the SDI OUT connector on the AW-PB504 SDI card or other card installed in the convertible camera. . AUX IN connector [AUX IN] This connector is connected using a BNC coaxial cable to the SDI OUT connector on the AW-PB504 SDI card or other card installed in the convertible camera or to the VBS connector on the AK-HDC1500G down converter board or other board installed in the AK-HC1500G multi-purpose camera. . TALLY OFF/ON switch [TALLY] When this is set to ON, the tally lamp is lighted by the selected signals. When it is set to OFF, the (.) tally lamp will not light even if the selected signals are supplied. 9 Parts...