Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
A A Set the satellite receiver brand code. Keep pressing SET UP down during step A. Enter your satellite receiver’s brand code using the number keys, then press ENTER. Press TV/CBL/SAT 1 on the unit’s remote control to turn on the satellite receiver and try operations (. step B). . Once you have set the remote control to operate the satellite receiver, you do not have to repeat this step until you replace your remote control’s batteries. . Some brands of satellite receiver have more than one code. If the satellite receiver does not function with one code, try entering another. B B Operate the satellite receiver. Press the corresponding button: TV/CBL/SAT 1, TV/ CBL DVD PR +/–, number keys. . For some brands of satellite receiver, you must press ENTER after having pressed the number keys. . The number keys may not function with some satellite receivers. BRAND NAME CODE JVC 73 AMSTRAD 60, 61, 62, 63, 92 CANAL SATELLITE 81 CANAL + 81 D-BOX 85 ECHOSTAR (VIA DIGITAL) 82 FINLUX 68 FORCE 89 GALAXIS 88 GRUNDIG 64, 65, 102 HIRSCHMANN 64, 78, 99 HUMAX 88 ITT NOKIA 68 KATHREIN 70, 71, 96 LUXOR 68 MASCOM 93 MASPRO 70 NOKIA 87, 94 PACE 65, 67, 74, 86, 92 PANASONIC 74, 92 PHILIPS 66, 84, 101 RADIX 78 RFT 69 SABA 97 SAGEM 83, 90 SALORA 68 SAMSUNG 83 SIEMENS 64 SKYMASTER 69, 98 TECHNISAT 66, 100 THOMSON 97 TPS 83 TRIAX 91 WISI 64 SYSTEM CONNECTIONS Connecting To A Satellite Receiver Connect the satellite receiver to the L-2 IN/DECODER connector, then connect the L-1 IN/OUT connector to the TV’s connector. NOTES: . Set “L-2 SELECT” to “VIDEO” or “S-VIDEO”. (. pg. 85) . You can use the Automatic Satellite Programme Recording function (. pg. 65) with this connection. . To record a programme via the satellite receiver, select L-2 mode by pressing PR +/– so that “L-2” appears on the front display panel. . For details, refer to the instruction manual of the satellite receiver. Outdoor unit Satellite cable Satellite receiver Aerial TV aerial cable 21-pin SCART connector Back of TV Aerial connector Mains outlet Back of unit ANTENNA IN ANTENNA OUT IMPORTANT: When you set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO” (. pg. 85, “L-2 Select Setting (L-2 SELECT)”), it is possible to view a satellite broadcast with the TV set to its AV mode even if the unit is turned off. When the unit is in Stop mode or recording, press on the remote control to turn off the VIDEO indicator on the unit. . If you turn on the unit when the satellite receiver’s power is off, nothing appears on the TV screen. In this case, turn on the satellite receiver, or set the TV to its TV mode, or press on the remote control to set the unit to the AV mode. Connecting To A Dolby Digital Decoder or An Amplifier With Built-in DTS These instructions enable you to connect your unit to a Dolby Digital decoder or an amplifier with built-in DTS. Back of unit Note for connection: Remove the protection cap from the optical cable. Optical cable Dolby Digital decoder or amplifier with built-in DTS To DIGITAL AUDIO input Coaxial cable (not provided) DIGITAL AUDIO OUT (OPTICAL) DIGITAL AUDIO OUT (COAXIAL) (not provided) Make connections. Connect the unit and a Dolby Digital decoder or an amplifier with built-in DTS using either an optional optical cable or an optional coaxial cable. NOTES: . For Dolby Digital sound, set “DIGITAL AUDIO OUT” to “DOLBY DIGITAL/PCM”. (. pg. 93) . For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/ PCM”. (. pg. 93) CAUTIONS: . This unit has a dynamic range of more than 110 dB with regards to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them. . Some speakers and televisions are specially shielded to prevent television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the playback picture. When you can’t switch the audio channel of a bilingual programme When the unit is connected with a digital audio device using an optional optical cable and “DIGITAL AUDIO OUT” is set to “DOLBY DIGITAL/PCM”, it is not possible to switch the audio channel of a bilingual programme recorded on a DVD-RAM or DVD-RW (VR mode) disc. In this case, perform the following steps using the remote control to switch “DIGITAL AUDIO OUT” from “DOLBY DIGITAL/PCM” to “PCM ONLY”. A Press SET UP to access the Main Menu screen. B Press we to select “DVD SET UP”, then press ENTER. C Press we to select “AUDIO OUTPUT”, then press ENTER. D Press rt to select “DIGITAL AUDIO OUT”, then press ENTER. E Press rt to select “PCM ONLY”, then press ENTER. (. pg. 93) F Press SET UP to complete the setting. G Press AUDIO to select the desired audio channel. (. pg. 36, “Audio Channel Selection”) SUBSIDIARY SETTINGS Various modes of this unit are categorized into menus nested in 2 levels shown in the following table. To change the settings of these modes, fi...
Эта инструкция также подходит к моделям:Видеонаблюдение - DR-M1SLB (8.47 mb)