Войти:
Оценок - 1, средний балл: 5 ( )

Инструкция по эксплуатации Chamberlain, модель CWA2000

Производитель: Chamberlain
Размер: 314.27 kb
Название файла: 28a01f62-2a7c-487c-8247-3d2c914fb4af.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


OPTIONAL AC Adapter Input A Ensure Base Station and PIR Motion Sensor are in close proximity to each other. Press and release Learn Button on Base Station. Buzzer will sound. B Within 60 seconds, press the Learn Button on the inside of the PIR Motion Sensor. LED light will illuminate and Base Station will buzz. Learn Button 1 2 PIR Motion Sensor SWITCH #1: SWITCH #2: 3 4 Learn Button Insert battery pack facing away from circuit board and fasten cover with the smallest screws (provided). NOTE: Ensure the batteries do not touch the circuit board and the antenna and battery wires are not pinched. 5 6 PIR MOTION SENSOR INSTALLATION Mount PIR Motion Sensor horizontally on solid surface 3-5 feet (1-1.5 m) off the ground and within 1/2 mile (0.8 km) of Base Station (rotate sensor to access screw holes). Unit should be able to swivel as needed. Attach sun/rain shield. NOTE: Keep PIR Motion Sensor antenna away from metal objects. Do not mount PIR Motion Sensor in direct sunlight, near moving tree branches, or in the path of a sprinkler system. 4 feet (1.2 m) 10-20 feet (3-6 m) Vehicle Alert Installation: For cars, the best mounting position is about 4 feet (1.2 m) high, between 10-20 feet (3-6 m) back, and angled to see the back of car after passing the sensor. 7 Test PIR Motion Sensor by waving hand in front of sensor. LED light should fl ash and the Base Station will buzz X number of times indicating which sensor has been activated. Troubleshooting The PIR Motion Sensor lights up, but the Base Station does not respond. The PIR Motion Sensor must be programmed to Base Station (See Step 4). Ensure Base Station is on and the volume is turned up. PIR Motion Sensor is detecting motion only part of the time. Ensure the PIR Motion Sensor is set to the High Sensitivity setting (See Step 2). To detect cars, it is best to mount PIR Motion Sensor at height of car’s motor and have it between 10-20 feet (3-6 m) from the road. Swivel sensor as needed. The Alert is giving false alarms. Check for moving tree branches or insects in sensor window. PIR Motion Sensor can also be triggered by light shining directly in sensor window, such as refl ected sunlight, or motion in front of a light source. It is possible that condensation has built up on the sensor. Wipe condensation from PIR Motion Sensor with cotton swab. Let it sit inside for a few hours, open to the air, without the batteries and it should correct itself. Check Sensor Switches on PIR Motion Sensor. See Switch Settings. Base Station beeps every 30 minutes. The batteries in the Base Station or the PIR Motion Sensor(s) are low. Replace the 4 AA batteries. Check the PIR Motion Sensor(s), if the LED illuminates on all of the PIR Motion Sensors, change the batteries in the Base Station. The Alert is not getting expected transmission range. Keep both antennas vertical and keep PIR Motion Sensor antenna away from trees and metal objects. Ensure Base Station is in clearest possible sight of the PIR Motion Sensor. The less objects between the devices, the longer the range. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifi cations to this equipment. Changes or modifi cations not expressly approved by the manufa...

Эта инструкция также подходит к моделям:
Видеонаблюдение - CWA2000C (314.27 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории