Оценок - 2, средний балл: 5 ( )

Производитель: Crimestopper Security Products Размер: 356 kb Название файла: Язык инструкции:

Using this option you can control whether the unit monitors the vehicle’s glow plug circuit using the Pink input wire (Default), or you may select a specific delay time Before cranking. This option is helpful if you are unable to locate a glow plug signal. Just select a delay time and do not connect the Pink Glow Plug wire. Selections: 10, 20, 30 seconds, or Monitor Pink Wire (Default). 23. REMOTE START ENGINE RUN TIME: Set engine run time for 12, 24, 36 or 48 minutes as desired. 24. ULTRA-SMART TACHLESS VOLTAGE ADJUSTMENT: This option controls the voltage reference point when using smart Tachless mode. Pressing the Lock or Unlock buttons on the remote raises or lowers the reference level in 1% increments from 80%-%100. Button #3 resets the unit to the factory default reference point of 93%. The default 93% setting works for most vehicles. See page 14 for additional Ultra-Smart Tachless mode information. 25. FACTORY HORN CHIRPS / PULSES: This option controls the system’s horn honk output. There are 3 selections: • Button 1 (Lock): Pulse horn when alarm is triggered. • Button 2 (Unlock): Pulse horn when alarm is triggered and Honk when Alarm is Arm and Disarm. • Button 3 (Trunk Pop): Pulse horn when alarm is Triggered, Honk when Alarm is Arm and Disarm and Pulse when Shock pre-warning is set off. (default) 26. Aux #3: (Violet/White wire) This option controls the function of the Violet/White wire for a negative output for a Momentary, Pulse, Timed or Latched output, depending on option used. Option #27 controls the length of time output. 27. Aux #3 Time control: (1 sec. to 255 sec.) Default = 12 seconds This option determines to length of time that is outputted from Aux #3 (Violet/White wire). Pressing the Lock or Unlock buttons on the remote raises or lowers the time by one second. 28. Aux #4: (Green/White wire) This option controls the function of the Green/White wire for a negative output for a Momentary, Pulse, Timed or Latched output, depending on option used. Option #29 controls the length of time output. 24 PROGRAMMABLE OPTIONS Cont. PROGRAMMABLE OPTIONS Cont. 29. Aux #4 Time control: (1 sec. to 255 sec.) Default = 12 seconds This option determines to length of time that is outputted from Aux #4 (Green/White wire). Pressing the Lock or Unlock buttons on the remote raises or lowers the time by one second. 30. Option Reset: RESTORE TO DEFAULT This option allows you to restore all programmable options to factory default values. Go to the option 30 and press the Unlock Button #2 on the remote. The lights flash 2 times and all values will be reset to factory original settings. Default values are marked with asterisks in the chart on pages 20. PROGRAMMABLE OPTION RESET This system provides a reset method to restore all options to FACTORY DEFAULT VALUES as listed in the “Button #2” column of the programmable option chart on pages 19-20. This can be helpful if you have lost track of the option settings on your system, or when you are moving the system from car to car and want a “clean slate”. 1. Open hood (ground the Blue wire if no hood pin is installed) 2. Turn Key to the ON position (Pink ignition wire must be connected) 3. Press program / valet button 5 times, after a few seconds the unit will flash the lights 5 times. 4. Push the valet/program button 30 times. Press carefully, do not lose count! You must get a light flash each time you press the button. If the unit didn’t flash the lights, then the system did not register your press. 5. Press button #2 (Unlock) to reset the options. (Lights should flash twice) 6. Turn Ignition OFF, Close hood (un-ground Blue wire). All features should be set at *DEFAULT values. PROGRAMMING – TRANSCEIVERS & TRANSMITTERS MAKE a NOTE of the following transmitter / transceiver compatibilities: • CS-2011DP 1-WAY SYSTEM: CS-511TX Remotes ONLY • CS-2012DP-TW1 2-Way System: CS-799LED Remote / CS-512TW “Sidekick” non-paging remote • CS-2014DP-TW2 2-Way System: CS-599FM LCD Remote / CS-519TW “Sidekick” non-paging remote • CS-2900DP-FM 2-Way System: CS-999FM LCD Remote / CS-519TW “Sidekick” non-paging remote Use the part numbers referenced above when ordering remotes. Some remotes are NOT interchangeable between systems. When re-learning remotes or adding remotes, ALL your system’s remotes must be learned at time of programming! These systems allow storage of up to 4 different remote codes in memo 25 REMOTE PROGRAMMING DIAGRAM REMOTE PROGRAMMING DIAGRAM 1. Turn key to the ON position.( doors will lock if autolock is programmed ) 2. Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times. 3. For CS2011DP systems: Press button #1 (Lock) of the transmitter; for 2-Way paging systems and “Sidekick” remotes: Press Buttons #1 & 2 together. You should get 2 light flashes indication the unit is waiting for a 2nd code, then press the same combination of buttons on a second remote, the unit will flash 3 times indicating its waiting for the 3rd ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: