Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
When used with an H511, video received from the H722 is used to create a new channel to add to existing television channels. The H722 is connected to the H511 by a single run of CAT-5 wire. Although this camera mount is intended for use indoors, or under an eave, a drip cap is supplied for use in exposed areas. Two models are available: Model H722 Model H722C Black & White, 2 lux, 3.6 mm lens, smoked window Color, 8 lux, 3.6 mm lens, smoked window Note: The H722 is not a standalone video camera Use only with an H511 channel injector. ChannelPlus Video Camera Typical Installation DECLARATION OF CONFORMITY THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC classifies this product under part 15 of its rules as a “television interface device”. Systems designed using television interface devices have the following legal requirements: 1) The modulated channel signal strength may not exceed 15.56dBmV at any television. 2) If an antenna is used in the system, the modulated channel signal strength may not exceed -51dBmV at the antenna input port. Any system you design must comply with these regulations. As the installer, you are responsible. The H722 or H722C (when used with an H511) has the necessary characteristics to comply with the above requirements as designed without additional accessories. The H511HHR is suitable for use with an antenna or with CATV systems. The H511BID is suitable for use with CATV systems only. Installation requirements: For the Installer: Federal Regulation 47CFR15.115(b)(1)(i). Federal Regulation 47CFR15.115(c)(4). Connect H511 output to splitter or distribution panel input. (See H511 manual) Output Program CATV /Ant Power Channel Injector CAT-5 video Connect antenna or incoming cable to H511 CATV/Ant input. Channel Injector (H511HHR shown) H722 (rear view) Connect the H722 camera using only method: 1 Terminate cable with a CAT-5 jack and connect to the H511 using supplied RJ45 jumper. (Also see example H628 manual). 2 Wire camera or wall plate directly to the 8 position terminal block matching the CAT-5 wire colors to the colors on the terminal block. Insert wires and tighten screws. one 1 2 Power the H511 last - make all cable and CAT-5 connections first. Installing the Camera Deep double-gang J-box Attach drip cap, gasket & frame drip cap Outside Installation Inside Installation gasket CADDY® bracket frame frame drip cap frame gasket Insert 6-32 screws into frame and bottom holes of 2 gang box Note: bottom lip of drip cap goes frame. (You may have to rotate drip cap 180 for proper placement.) inside o Add top screws 3 2 Aiming the Camera Attaching the Window Rotate downward and snap into place. Window rides on the lip of the frame. 4 5 The H722 is designed to be mounted outside in a J-box or inside into dry wall. When mounting outside, use the supplied drip cap and gasket. When mounting inside, use the supplied CADDY® bracket. The H722 series cameras work best when they are looking down on their subject. For a front door application, place the camera about 7 feet off the ground, adjacent to the door. Add RTV to seal from weather 3.6mm F2.0 >45 dB 8 lux Yes 1/60 to 1/50000 second automatic 78O 100 feet 3.6mm F2.0 >45 dB 2 lux Yes 1/60 to 1/50000 second automatic 78O 300 feet Resolution, horizontal 525 lines 525 lines Specifications: typical @ 25 C ± 5 C O O Model H722 H722C Image format EIA (Black & White ) NTSC (Color) Resolution 350 lines 350 lines Lens Signal to Noise ratio White balance Minimum illumination Lens viewing angle AGC Electronic shutter speed Maximum distance to H511 Maximum CAT-5 run: H722 to H511 300 feet H722C to H511 100 feet Insert wire into terminal block and tighten screws. Use the color bar to match wire colors. The color bar has two rows, one for CAT-5 and one for quad wire: - For CAT-5 wire, remove the default resistor and use all 8 wires. - For quad wire , leave default resistor in place and match four color wire. The H722/H722C was designed to work with CAT-5 wiring. Although the system will function with quad wire, CAT-5 delivers the highest quality picture. CAT-5 allows the use of an automatic line length sensor and picture compensator. Quad wire does not take advantage of this enhancement. * 1 1 Insert 6-32 screws into frame and bottom holes of CADDY® bracket. Drywall Use these parts Use these parts CADDY® bracket Make a square cut-out in the drywall that is 3.” wide by 3.” high. Insert clip into drywall, and bend to form. Prepare the CAT-5 wires by stripping 1” of outer sheath and 1/8” of insulation. Insert wires into 8 position terminal block and tighten screws. Insert 1/8“ screwdriver in the steering slot below the lens. Using the screwdriver, bend the mount to point the camera in the desired direction. Never use camera to bend...
Эта инструкция также подходит к моделям:Видеонаблюдение - H722C (699.26 kb)