Оценок - , средний балл:
(
)
)
Производитель: DeWalt
Размер: 8.81 mb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
The character that is being changed will be underlined. To move back a character, use the down arrow. To move forward a character, use the up arrow. Basic Operations 8 English 10. Select SET. 11. Choose AM or PM. The up and down arrows AM and PM. 12. Select SET. IMPORTANT: If for any reason the system is disarmed after site still requires protection, the system will need Remote or keypad. The following day, the auto arm will continue to auto arm at the preset time. Disarming the System Deactivating the system to be able to make changes, open alarm response. • Entry Delays • Using the Keypad • Using the Key Chain Remote ENTRY DELAYS Each sensor aside from the Base Unit motion sensor can be reset for Instantwhich elim inates the entry delay. By changing a device to instant, when the system is armed an alarm will take place as soon as the device is tripped. IMPORTANT: The vibration sensor in the Base Unit is automatically set to instant. This set ting cannot be changed. The purpose of this setting is to send a notification if an intruder attempts to disable or destroy the device. IMPORTANT: To avoid a false alarm, sensors that are likely to be tripped as the user enters and exits the site to arm/disarm the unit should remain set on delay mode. For more information, see Set Delay/Instant under Features and Options. USING THE KEYPAD IMPORTANT: Avoid causing vibration in the Base Unit when typing the master code. The vibration sensor will be on as soon as the internal motion detector recognizes motion. When a vibration occurs, the unit will send an alarm. This is to provide protection of damage or destruction of the Base Unit. If the vibration sensor is accidentally tripped, the system will immediately contact the monitoring system. When the system is armed, the Armed screen will be displayed: 1. To disarm the code. 2. The main screen The ARMED light on USING THE KEY CHAIN REMOTE Use the Key Chain Remote for one-Base Unit. When the system is armed, the Armed screen will be displayed: 1. To disarm the system, press the disarm button on the right side of the Key Chain Remote. 2. The main screen will be displayed. The ARMED light on the unit will be off. Faults Faults indicate when there has been a serious issue that needs to be addressed. This could be a number of things including an unsecured device, low battery, tamper and weak signal. • How to View Faults • Clearing a Fault • Description of Fault Codes HOW TO VIEW FAULTS If a fault is present, the system will display the Fault screen. 1. To clear, select SILENCE. This will simply allow the system to be armed over a fault. It is recommended to correct the fault as soon as possible. To display the fault and resolve immediately, select DISPLAY. 9 2. The fault faults. Resolve Description chart and the Fault screen To remove a tamper IMPORTANT: See the Description of Fault Codes for more details regarding a fault resolution actions. All faults, except a tamper, will automatically be cleared when the issue has been resolved. An event will be recorded in the event that the event occurred and was resolved. NOTE: A tamper fault will not be automatically cleared. After the device has been inspected, checked for damage, and the cover See Clearing a Fault. This process was designed to create awareness with the master user and require verification that the CLEARING A FAULT To clear any fault other than a tamper fault, correct the condition For example: replace the battery, relocate to an area with a better signal, etc. To Clear a Tamper Fault: IMPORTANT: Before clearing a tamper fault, be sure that the issue has been resolved. Only the master user can clear tamper faults. 1. When the Fault Code screen is displayed; select CLEAR. 2. Use the keypad to enter the master code. 3. Select OK. DESCRIPTION OF FAULT CODES NOTE: See the Troubleshooting Guide for more detailed information. DESCRIPTION OF FAULT CODES Fault Code Fault Display Description Action Power Primary Power Lost Base No power to Base Unit Check power supply DevPower Primary Power Lost Device # No battery power in device Change battery, reset BaseLowBatt Base Low Battery Base Unit battery low Plug in power supply to recharge battery DevLowBatt Low Battery Device # Device battery low Change battery, reset WeakSig Weak Signal Device # Transmission signal from device is weak Check for interference; move device Unsecured Unsecured Device # Device has been tripped Check for intrusion; re-secure device NoCheckIn No Check In Device # Device check-in messages have not been received Check for interference; move device DESCRIPTION CODES cont. Fault Code Fault Display Description Action Tamper Tamper Device has been opened or damaged Close device or replace if damaged BaseBadBatt Bad Battery Base Base Unit battery has dropped below the voltage limit Needs to be repaired at DEWALT authorized service center CellRadio Cell Radio Fault Cellular radio signal is lost or scrambled Move Base Unit to a location where CELL light is soli...
Эта инструкция также подходит к моделям:Видеонаблюдение - DS100 (8.81 mb)