Also, if rehearsal is to be interrupted at this point, press the [STOP] button. 4. Change to the address to be recorded with the [JOG] dial. 5. After completing rehearsal, a SKIP-ID can be recorded if the [WRITE] key is pressed again. During recording of SKIP-ID, the WRITE LED will change from blinking to constant lighting and [SKIP-IDj will be shown in the display. Simultaneously with finish of the recording, the SKIP LED of the [ID SELECT] key and the WRITE LED will be extinguished and D-15 will PAUSE, * If recording is to be carried out again at a different point, repeat steps 1-5. 5-2-3. Erasing the SKIP-ID Unnecessary SKIP-ID's can be erased. < NOTE 1> This will not operate in the INSTANT START mode. This will not operate if the cassette tape erase prevention hole is open. Operating procedure 1. Find the SKIP-ID to be erased by playback, fast forward or rewind modes and show it in the [SKIP-ID] display. 2. Press the [ID SELECT] key and select SKIP (SKIP LED will be lit). 84 D-15 Owner’s Manual (Chapter 5 Record/Erase of Sub-ID) 3. Confirm that [SKIP-ID] is shown in the display and press the [ERASE] key. When the key is pressed, the transport will search for the SKIP-ID located within 9 seconds (300 frames) from the stopped position and erase it 5-3. Record/Erase of END-ID Record/Erase of the END-ID is explained here. Same as for SKIP-ID, recording of the END-ID by D-15 is possible in the following two methods: ® 1. Record END-ID at any position during recording. ' 2. During playback of a prerecorded tape, make minute adjustments in the rehearsal (RAM REPEAT playback) mode and then, record the END-ID. 5*3-1. Record the END-ID at any position during a recording In this chapter, END-ID is recorded manually at any point during recording of AUDIO DATA. < NOTE> Recording is not possible if the cassette tape erase prevention hole is open. Operating procedure 3 (WRITE key) □ o i boitai. master ateoner* 15 “ÈFB □ □□ □ □ o a <0 □ t> ta q □ q 0 'û '□ '□ a nODQ.j? -tA-bs ss j ^ a «,<=] □ o o a q: qe o ,f°g° ü o o 2 (ID SELECT key) (RECORD + PLAY buttons) 1. While pressing the [RECORD] button, press the [PLAY] button to start recording. Should recording be carried out with the SETUP mode *106 - rECid remaining switched "ON," S-ID will be recorded at the point where automatic recording was executed. If S-ID is not to be recorded at this point, the SETUP mode *106 - setting must be switched "OFF" before starting to record. D-15 Owner's Manual (Chapter 5 Record/Erase of Sub-ID) 2. Press the [ID SELECT] key and select "END” (END LED is lit) prior to startin the recording. 3. Press the [WRITE] key when tape arrives at the position where END-ID is to be recorded. [END-ID] will be shown in the display during recording of END-ID and be extinguished at finish of recording. Also, END LED of the [ID SELECT] key will be extinguished at the same time. * At finish of recording the END-ID, it automatically REWINDS and PAUSE at two seconds before the END-ID. 5*3-2. Do Rehearsal, Then Record END-ID During Playback of a Prerecorded Tape Here, END-ID is recorded at any position during playback of a prerecorded tape. In this operation, the position where END-ID is to be recorded is minutely adjusted by rehearsal of RAM REPEAT for recording in an accurate position. < NOTE 1 > This process cannot be executed if no A-TIME is recorded on the tape. If END-ID already exists in the vicinity where recording is to be made, erase this END-ID prior to operation. It will not operate if the cassette tape erase prevention hole is open. It will not operate if tape is played back in the INSTANT START mode. Operating procedure (PLAY button) 2 (ID SELECT key) D-15 Owner's Manual (Chapter 5 Record/Erase ofSub-ID) 1. Start playback by pressing the [PLAY] button. 2. Prior to playback, press the [ID SELECT] key and select "END" (END LED will be lit). 3. Press the [WRITE] key once upon arriving at the point where END-ID is to be recorded. It will enter the INSTANT START mode at the instant this key is pressed and simultaneous with blinking of the [WRITE] key LED, RAM REPEAT playback (rehearsal) will be repeated for about one second from the time when the key was pressed (The display, at this moment, will show the time at which the key was pressed). * At this point, if the [WRITE] key is pressed twice in succession, END-ID can be recorded without conducting a rehearsal. Also, at this point, if rehearsal is to be interrupted, press the [STOP] button. 4. Change to the address for recording by manipulating the [JOG] dial. 5. After completing rehearsal, an END-ID can be recorded if the [WRITE] key is pressed again. During recording of the END-ID, WRITE LED will change from blinking to lighting and [END-ID] will be shown in the display. * At finish of recording the END-ID* it automatically REWINDS and PAUSE at two seconds before the END-ID, 87 ...
)
