Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
Installation GB59 10.1 Channel Search 10.2 Linear Search 10.3 Default Setting GB59 GB62 GB64 11. Software Update GB65 11.1 OTA (Over the Air) GB65 12. System Information GB68 12.1 Status 12.2 Signal Detection 12.3 Conditional Access (for Conax embedded) GB68 GB68 GB69 13. Games GB70 14. Menu Map 15. Troubleshooting GB71 GB72 15.1 Troubleshooting 15.2 Error Message GB72 GB73 16. Specification 17. Glossary 18. Service and Support GB74 GB76 GB77 GB 7 1. Before Using the Recorder 1.3 Rear Panel 1. CABLE IN Connects a cable to a CABLE input jack on the Recorder. 2. TV/VCR Connects a RF signal from your recorder to RF(ANT) input jack on your TV or VCR. 3. TV SCART Connects a TV SCART cable. 4. VCR SCART Connects a VCR SCART cable. 5. S/PDIF Outputs the digital audio signals. 6. VIDEO Connects to your TV or VCR and output Video signals. 7. AUDIO L/R Connects to your TV or VCR and output Audio signals. 8. RS-232C Connects to your PC to upgrade product's software programme. 9. ON/OFF Power on/off. GB 10 1.4 Conditional Access Although some TV and Radio channels are free to air, most TV and Radio/Music channels are available on a subscription basis and can only be enjoyed via Conditional Access component. The Conditional Access component is removable Smartcard. Inserting Smartcard A Smartcard looks similar to a credit card and entitles you to view and listen to all the channels you choose to subscribe to. The Smartcard slot on the product can be used for Conax Smartcard only. 1. Open the right-hand flap on the front panel of the product. 2. Hold the Smartcard horizontally with the electronic chip (generally small square, gold in colour) facing upwards. 3. Insert the Smartcard into the top slot until the card is completely in. ** GB 11 1. Before Using the Recorder 1.5 Remote Control Unit GB 12 ** 1. SOURCE Selects the input source between TV and recorder. 2. TV/RADIO Switches between TV and Radio modes. 3. NUMERICAL (0~9) BUTTONS Enters a TV/Radio channel number or menu option number. 4. LIST Displays the channel list. 5. BACK Returns to the previous menu and screen. 6. ARROW BUTTONS Changes the channel or move the cursor to the up, down, left or right menu option. 7. OPT+ (OPTION) Displays the channel attributes during watching a programme. 8. AUDIO Displays the Audio list. 9. CH-/CH+ and PAGE-/PAGE+ Changes the Channel or Page. 10. MENU Displays the main menu. 11. PLAYBACK CONTROL BUTTONS Includes fast rewind, play, fast forward, record, stop, pause buttons. 12. STANDBY Switches between Operation and Standby modes. 13. GUIDE Displays the Programme Guide. 14. EXIT Exits the main menu or Guide screen. 15. OK Selects a menu, or confirms the selected operation. And displays the channel list during watching a programme. 16. G (Game) Displays the Game. 17. SUBTITLE Changes the subtitle language. 18. V-/V+ Adjusts the audio volume. 19. i (INFORMATION) Displays the information about the channel and programme. 20. MUTE Pauses the audio temporarily. That is, volumes on/off temporarily. GB 13 2. Setup This chapter describes how to set up the Recorder. Select the most appropriate procedure depending on your requirements. Note: If you encounter any problem when setting up the Recorder, please contact your local product distributor. 2.1 Connecting the Cable 1.ConnectingTV This is the most simple setup mode. • Connect your CATV line to the CABLE IN socket on the Recorder for receiving cable services. • TV Scart are connected as in the figure above. GB 14 2.ConnectingTV/VCRwith2SCARTs2.ConnectingTV/VCRwith2SCARTs This is the optimal way to connect the Recorder. ** GB 15 2. Setup 3.ConnectingHi-Fisystem If you wish to connect S/PDIF to the optical S/PDIF terminal and Dolby digital decoder to listen digital audio, connect as following. GB 16 2.2 Powering On 1. Connect the power cord of the recorder to a wall outlet. 2. Turn on the power switch, located at the left on the back of the recorder. Make sure that the Standby LED indicator is turned on Red. ** 3. Power on by pressing the STANDBY button at Remote Controller. GB 17 3. Installation Wizard When powering on your product for the first time after purchasing, the Installation Wizard is automatically started. You can easily set-up using simple organisation and options, and watch the broadcasting after completing the set-up procedure. You can select items using the NUMERICAL (0-9) button. Note: If you press the BACK button or select Back and press the OK button while running the Installation Wizard, you can return to the previous screen. 3.1 Language Select the appropriate language from the list using the button and press the OK button to save the selected language as a default language for Menu, Subtitle, and Audio. 3.2 Area Setting The country is fixed to Sweden. GB 18 ** 3.3 Channel Search You can set parameters to search channels. Select the following item using the button, and press the OK or button. • Frequency: The default value is set to 362000. If you wish to set your desire...