Оценок - 2, средний балл: 3.5 ( )

Производитель: Sony Размер: 897.92 kb Название файла: Язык инструкции:

Do not use any type of solvent, such as alcohol or benzine. The Line Through function does not operate. • Set POWER SAVE in the USER SET menu to OFF (see page 62). Additional continued Troubleshooting Symptoms caused by contaminated video heads • Normal picture • Rough picture • Unclear picture • No picture (or black & white screen appears) initial terminal contamination Troubleshooting Specifications System Channel coverage PAL (I) VHF IA to IJ, SA10 to SA13* UHF B21 to B69 CATV S01 to S05, S1 to S20* HYPER S21 to S41* RF output signal UHF channels 21 to 69 Aerial out 75-ohm asymmetrical aerial socket Tape speed SP:PAL23.39 mm/s (recording/playback) NTSC33.35 mm/s (playback only) LP:PAL11.70 mm/s (recording/playback) NTSC16.67 mm/s (playback only) EP:NTSC11.12 mm/s (playback only) Maximum recording/playback time 10 hrs. in LP mode (with E300 tape) Rewind time Approx. 1 min. (with E180 tape) * SLV-SE730I and SE230I only Inputs and outputs LINE-1 (EURO AV) 21-pin Video input: pin 20 Audio input: pins 2 and 6 Video output: pin 19 Audio output: pins 1 and 3 LINE-2/LINE-3 21-pin Video input: pin 20 Audio input: pins 2 and 6 t LINE-2 L o R*1 VIDEO IN, phono jack (1) Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative AUDIO IN, phono jack (2) Input level: 327 mVrms Input impedance: more than 47 kilohms AUDIO (OUT) R, L*2 Phono jack (2) Rated output level: 327 mVrms Load impedance: 47 kilohms Output impedance: less than 10 kilohms *1 SLV-SE830G only *2 not available on SLV-SE230G/I General Power requirements 220 – 240 V AC, 50 Hz Power consumption • SLV-SE230G/I 15 W 1.2 W (POWER SAVE is set to ECO2, minimum) • SLV-SE830G, SE730G/I 17 W 1.3 W (POWER SAVE is set to ECO2, minimum) Operating temperature 5° C to 40° C Storage temperature –20° C to 60° C Dimensions including projecting parts and controls (w/h/d) Approx. 360 . 95 . 245 mm (SLV-SE230G/I) Approx. 430 . 96 . 245 mm (SLV-SE730G/I) Approx. 430 . 96 . 253 mm (SLV-SE830G) Mass Approx. 2.8 kg (SLV-SE230G/I) Approx. 3.1 kg (SLV-SE830G and SE730G/I) Supplied accessories Remote commander (1) R6 (size AA) batteries (2) Aerial cable (1) Design and specifications are subject to change without notice. Additional Specifications Additional Operations Playing/searching at various speeds Before you start… • Refer to “Index to parts and controls” for button locations. Playback options Operation View the picture during fast-forward or rewind During fast-forward, hold down M (fast-forward). During rewind, hold down m (rewind). Play at high speed • During playback, press M (fast-forward) or m (rewind) on the remote commander. • During playback, hold down M (fast-forward) or m (rewind). When you release the button, normal playback resumes. Play at twice the normal speed During playback, press .2. Play in slow motion During playback, press y SLOW. Play frame by frame During pause, press M (fast-forward) or m (rewind)* on the remote commander. * SLV-SE830G only To resume normal playback Press H (play). Using the shuttle ring (SLV-SE830G only) JOG With the shuttle ring, you can operate a variety of playback options. There are two ways for using the shuttle ring, normal mode and jog mode. Shuttle ring Playing/searching at various speeds To use the shuttle ring in normal mode During playback or pause, turn the shuttle ring clockwise or anticlockwise. Each change in the shuttle ring position changes the playback mode in the following way. Pause Slow motion in reverse Normal speed in reverse Double speed in reverse Slow motion Double speed Normal speed (Initial speed) High speed in High speed reverse To use the shuttle ring in jog mode Use this mode for frame-by-frame playback. Press JOG to enter the jog mode. The JOG button lights up. If you change to the jog mode during any playback mode, playback pauses so you can see a still picture. Each change in the shuttle ring position shifts the picture one frame. To shift frames in reverse, turn the shuttle ring anticlockwise. The frame shift speed depends on the speed you turn the shuttle ring. To resume normal mode, press JOG again. The JOG button turns off. Tip • Adjust the picture using the PROGRAM +/– buttons on the VCR if: –Streaks appear while playing in slow motion. –Bands appear at the top or bottom while pausing. –The picture shakes while pausing. To set tracking to the centre position, press both buttons (+/–) at the same time. Notes • The sound is muted during these operations. • In the LP mode, noise may appear or there may be no colour. • If the playback mode mark does not appear on the TV screen, press DISPLAY. • The picture may show noise when playing at high speed in reverse. • The picture returns to normal playback from slow motion in reverse in 30 seconds. Additional Playing/searching at various speeds Setting the recording duration time After you have started recording in the normal way, you can have the VCR stop recording automatically after a specified duration. Before you start… • Refer to “Index to parts and co...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: