Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
TUNER PROG 7 SYSTEM [D/K ] NORMAL/CATV [NORM] CHANNEL SET [S01 ] AFT [ON ] FINE TUNING SELECT : Vv SET : Bb 6 PAUSE Press ? // repeatedly until the channel you want is displayed. REW PLAY OK FF STOP The channels appear in the following order. TUNER PROG 7 SYSTEM [D/K ] NORMAL/CATV [NORM] CHANNEL SET [C02 ] AFT [ON ] FINE TUNING SELECT : Vv SET : Bb D/K TV system B/G TV system CHANNEL SET Corresponding CHANNEL SET Corresponding number TV channel number TV channel 2 R1 2 E2 5 R6 3 E3 6 R7 4 E4 12 R12 5 E5 13 R2 6 E6 14 R3 7 E7 15 R4 8 E8 16 R5 9 E9 17 R8 10 E10 18 R9 11 E11 19 R10 12 E12 20 R11 21-69 E21-E69 21-69 R21-R69 CATV 1-41 S1-S41 CATV 42-46 S01-S05 Getting Started PAUSE PLAY OK If the TV sound is distorted or noisy, press >/.to move the REW FF cursor ( ) to SYSTEM, then select B/G or D/K so that you get the better sound. STOP TUNER PROG 7 SYSTEM [B/G ] NORMAL/CATV [NORM] CHANNEL SET [C02 ] AFT [ON ] FINE TUNING SELECT : Vv SET : Bb To allocate another channel to another programme position, repeat steps 3 to 7. 9 PAUSE FFREW PLAY OK Press OK. STOP Disabling unwanted programme positions After presetting the channels, you can disable unused programme positions. The disabled positions will be skipped later when you press the PROG +/– buttons. 1 In step 6 above, press ? // repeatedly to display the number “00” beside CHANNEL SET. 2 Press OK. If the picture is not clear Normally, the Auto Fine Tuning (AFT) function automatically tunes in channels clearly. If, however, the picture is not clear, you may also use the manual tuning function. 1 Press PROG +/– to select the programme position for which you cannot obtain a clear picture. 2 Press MENU, then select SETTINGS and press OK. 3 Select TUNER and press OK. Selected programme position 4 Select FINE TUNING. The fine tuning meter appears. 5 Press ? // to get a clearer picture, then press OK. The menu disappears. Note that the AFT (Auto Fine Tuning) setting switches to OFF. TUNER PROG14 SYSTEM [D/K ] NORMAL/CATV [CATV] CHANNEL SET [S01 ] AFT [OFF ] FINE TUNING SELECT : Vv SET : Bb Getting Note • The menu disappears automatically if you don’t proceed for more than a few minutes. 17 Getting Started Basic Operations Playing a tape REPLAY 6 EJECT 03 REW P PAUSE . PLAY )# FF p STOP COUNTER RESET DISPLAY NTSC PB 1 Turn on your TV and set it to the video channel. 2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab removed. 3 PLAY OK Press . PLAY. When the tape reaches the end, it will rewind automatically. Basic Operations Additional tasks To Press Stop play p STOP Pause play P PAUSE Resume play after pause P PAUSE or . PLAY Fast-forward the tape )# FF during stop Rewind the tape 03 REW during stop Eject the tape 6 EJECT To replay a recently watched scene You can immediately rewind and playback the scene you want to watch again. During playback, press REPLAY up to four times. The VCR rewinds the tape about 10 seconds on the counter for each press of the button, and restarts playback. To play an NTSC-recorded tape Set NTSC PB at the rear of the VCR according to the colour system of your TV. When your TV is Set NTSC PB to PAL only ON PAL TV Basic Operations PAL and NTSC NTSC 4.43 To use the time counter At the point on the tape that you want to find later, press COUNTER RESET. The counter in the display window resets to “0:00:00.” Search for the point afterwards by referring to the counter. To display the counter on the TV screen, press DISPLAY. continued Basic Operations Playing a tape (continued) Notes • Tapes recorded in the LP mode cannot be played back on this VCR. • The counter resets to “0:00:00” whenever a tape is reinserted. • The counter stops counting when it comes to a portion with no recording. • When you play back the tape recorded with the NTSC colour system, the counter does not appear on the TV screen. • Depending on your TV, the following may occur while playing an NTSC-recorded tape: – The picture becomes black and white. – The picture shakes. – No picture appears on the TV screen. – Black streaks appear horizontally on the TV screen. – The colour density increases or decreases. – Deterioration of the picture quality may occur. • If a tape has portions recorded in both PAL and NTSC systems, the time counter reading will not be correct. This is due to the difference between the counting cycles of the two video systems. • While setting the menu on the TV screen, buttons for playback do not function. Basic Operations Recording TV programmes DISPLAY INPUT SELECT r REC TV/VIDEO PROG +/– COUNTER/ REMAIN p STOP Basic Operations 1 Turn on your TV and set it to the video channel. 2 Insert a tape with its safety tab in place. INPUT Press INPUT SELECT until a programme SELECT position number appears in the display window. continued Basic Operations Recording TV programmes (continued) 4 PROG Press PROG +/– to select the programme position you want to record. 5 Press r REC to start recording. REC The record...