For example, if you needed to enter 0 -5 to tune to channel 5, you need to "tell” the TV/HDR Combo this information during the on-screen setup. To update this information, go back to “Setup” to adjust the code for your cable box or DSS receiver. 1. Press MENU on the TV/HDR Combo remote. 2. Choose “Setup” from the Main Menu, then choose “Change Dialing & Input Settings.” 3. From the Setup Summary screen, choose the input that your cable box or DSS receiver is connected to. 4. Proceed through the steps to configure your box until you reach the screen that asks for your cable box or DSS receiver setup code. 5. Press the T button to dear the setup code: A. If your TV/HDR Combo required 2 digits to tune to a one-digit channel, enter the code for your TV/HDR Combo but replace the first digit with the number 6. B. If your TV/HDR Combo required 3 digits to tune to a one-digit channel, enter the code for your TV/HDR Combo but replace the first digit with the number 8. See page 16 to find your code. 6. Continue through the remaining screens and complete the setup. 7. Once you have completed setup, try changing the channels on your cable box or DSS receiver. 8. If you are still having trouble changing channels, repeat step 5 above with the following changes: • If you used step 5A. replace the number 6 with the number 7. • If you used step 5B, replace the number 8 with the number 9. My cable box sometimes fails to change channels when using the TV/HDR Combo remote control. • If you are using the IR blaster, your cable box receives IR commands from both the TV/HDR Combo remote and the IR blaster. Some cable boxes can be confused by this. You can prevent your cable box from receiving the commands from the TV/ HDR Combo remote control by affixing an opaque covering around the area where you have placed the IR emitter on your cable box. Don’t cover the IR emitter. The TV/HDR Combo does not respond when 1 press buttons on the remote control. Or, the image on my TV screen is "frozen." • Press and hold INPUT and CH ▼ on the front of the TV/HDR Combo for 10 seconds, then release. The TV/HDR Combo will restart in a few moments. • Unplug the AC Power Plug for one minute then plug it back in. The TV/HDR Combo will restart and power on in a few moments. Miscellaneous Solution When selecting a show from the Channel Guide, 1 get a screen that fades to blue. • Typically, this is caused by a weak video source. Contact Technical Support for further suggestions by phone at 1-888-843-9788. Phone support personnel answer calls between 6:00 AM and 6:00 PM (PST), Monday through Friday. When viewing show content through the TV/HDR Combo, shows appear to be in black and white. • This condition will exist if you have a composite input source going into the TV/HDR Combo on LINE 2, but the input source in Setup (on LINE 2) is set to S-Video. Go to “Changing Dialing & Input Settings” on page 18 to correct the information. When 1 select a channel in the Channel Guide, the channel number does not change on my DSS receiver or cable box. • If you’re using an IR blaster connection to control channel changing, verify that you have affixed the IR blaster directly in front of the IR detector on your cable box or DSS receiver. • Confirm that you have selected the correct IR code for your cable box or DSS receiver. (See page 16 for a list of codes.) When 1 select a channel in the Channel Guide, 1 get a blue screen that states “no video source...” • Confirm that you subscribe to the channel in question. • Verify that the AN connections going from your cable box/DSS receiver to the TV/HDR Combo are correct. • Verify that all your devices are turned on. When selecting a show in the Channel Guide, 1 get a solid blue screen. • Confirm that you have the correct input source specified in Setup. Go to “Changing Dialing & Input Settings” on page 18 to correct the information. The "FAN LOCK DETECTED PLEASE REFER TO MANUAL” message appeared. • The TV/HDR Combo is in need of repair. Contact Technical Support for further suggestions by phone at 1-888-843*9788. Phone support personnel answer calls (Monday-Friday 9am-9pm EST, Saturday-Sunday 9am-7pm EST including Holidays). 1 can not record pictures from my video camera on my TV/HDR Combo. • The TV/HDR Combo is not designed to record the pictures from other devices. 49 Frequently Asked Questions Questions Answers I can’t find the IR Blaster code for my cable box or satellite receiver. Call Panasonic customer support at 1-888-843-9788 to get the latest IR Blaster codes. The IR Blaster code listed for my cable box/DSS receiver does not work. Try substituting a 6, 7, 8, or 9 for 0 in the first digit of the code. The remote changes are inconsistent when changing channels. Affix an opaque covering around the IR Blaster, covering all IR receiver area not covered by the IR Blaster. The audio and video are not in sync with each other. Ensure that the audio from signal source is connected to the TV/HDR...