Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Two-way or two-track recordings cannot be made. ■ Keep the VTR away from flower vases, tubs, sinks, etc. CAUTION: If liquids should be spilled into the VTR, serious damage could occur. If you spill any liquid into the VTR, remove power and consult qualified service personnel. ■ Wipe the VTR with a clean, dry cloth. Never use cleaning fluids, chemicals' or wax. ■ Do not attempt to disassemble the unit. There are no user serviceable parts inside. ■ If any liquid spills inside the unit, have the unit examined for possible damage. ■ Refer any needed servicing to authorized service personnel. Dew Indication When dew is detected, the safety device of this unit will operate in order to protect the cassette tape and video heads. In case of dew detection, the “ J " mark in the counter lights. Wait until the “ J ” mark goes out with Power switch turned ON to operate the VTR. " d " mark lights. -- d I Note Dew condensation normally occurs gradually. Therefore, there may be cases in which the “ " mark does not start flashing until 10 or 15 minutes after dew has begun to condense. In particular, if the temperature or humidity in the room change, wait about 20 minutes before using the unit. Cause of Condensation Condensation forms if warm air comes in contact with a cold object, for example on a window in a well-heated room in winter. It may form if the unit or the video cassette is exposed to sudden changes in temperature and humidity such as may occur when the unit or the video cassette is taken from a cold to a warm place. For instance: ■ In a room where the heater has just been turned on in winter; ■ In a room with steam or high humidity; ■ If the unit or the cassette is brought from cold surroundings into a well-heated room. Cleaning care for video heads If the screen should appear as shown below, it means that the video heads are dirty. It is recommended that you clean the heads periodically. Use the optional cleaning tape and special purpose cleaning fluid to clean the heads. Consult with your dealer if the symptoms should persist even after cleaning. Notes: • We do not recommend that you attempt to clean the video heads yourself. • Repeated head cleaning will shorten the service life of the video heads. • Nothing can be recorded on the head cleaning tape. • If you use cleaning fluid, wipe the cleaned heads with a dry cloth before using the unit. - 18 - Troubleshooting Check out the points in the table given below, and consult with your dealer if the trouble should persist. Trouble Checkpoint/Remedial Action Ref. Page No power • Has the power cable been connected? No operation even when an • Is the power switch in the ON position? — operation button is pressed • Has a cassette tape been loaded? • Is “ d " displayed indicating condensation lighted? Keep the power supplied to the unit and wait until the “ d " in display goes off. 18 • Is the Mode Lock Switch at the OFF position? 14 No recording • Has the tape’s accidental erasure prevention tab been broken out? ----- • Has the INPUT Selector been set to the proper position? 13 Noise appears on playback pictures. • Press the Tracking Buttons and adjust. 14,15 No repeat playback • Has the MEMORY (MEMO) Button been set to the proper position? 10 • Has the counter been reset? 10 • Is the VISS setting on the menu screen at OFF? 8 • Has an interval of at least 20 seconds been given between r BEGIN and END? 12 No VISS signal writing • Is the VISS setting on the menu screen at REC or REC/PAUSE? • Has an interval of at least 30 seconds been given between 8 one VISS and another VISS signal? •11 Error Display The following error messages will be displayed on the tape counter if an abnormality occurs in the unit. In this case, follow instructions described below. ■ When an error code appears: • An error code appears on the display. • All operations are shut down when an error code appears on the display. • If the error is not released even after taking the remedial action described below, switch off the power, disconnect the power cable from the power outlet, and contact your dealer immediately. ■ List of error codes Error Code Malfunction Remedial action E-P Malfunction in elevator section These errors may occur if the video cassette has not been loaded properly. Try switching the power off and turning it back on again. E-3 Malfunction in loading section E-H Malfunction in cylinder section These errors may occur if there is something wrong with the state of the video cassette. Try switching the power off and turning it back on again and replacing the video cassette. E-S Malfunction in reel section C - c C o Incorrect tape tension E-l Malfunction in solenoid Try switching the power off and turning it back on again. - 19- Specifications Rating Input: 120 V AC, 50-60 Hz, 0.5 A General Recording System: 2-head helical scanning, azimuth recording Color System: NTSC color signals Heads: 4 video head...