Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
1 1 Turn on the DBS receiver Turn on the DBS receiver using the Power button on the DBS receiver or its Remote. 2 2 Enter DBS receiver brand code Follow the example shown below. 1 Press and hold CABLE/DBS. 2 Press MBR SET. 3 Press the Number keys to enter your DBS receiver’s brand code by referring to the table below. 4 Press OK, and release CABLE/DBS. The DBS receiver should turn off. If it does, try other operations below ( step 3). . Once you have set the Remote to operate the DBS receiver, you do not have to set it until you replace the batteries from the Remote. 3 3 Operate DBS receiver While holding down CABLE/DBS, press one of the following buttons: POWER, TV CH +/–, and Number keys. . For some brands, you must press ENTER after having pressed the Number keys to enter a channel number. . To change the DBS receiver’s channels, press TV CH +/– or the Number keys. (The CH +/– button can be used to change the VCR’s channels only.) NOTES: . Depending on the type of DBS receiver, some or all functions cannot be operated using this Remote. . It’s not possible to operate a DBS receiver not equipped with a remote sensor. . It's not possible to set the Remote for both your DBS receiver and a cable box at the same time. You can only set the Remote to operate one of these units at a time. (Ex.) To set the Remote to JVC 51: 5 CABLE/ DBS MBR SET A/B 1 OK3 Release Hold Press in succession down 1 2 3 4 5 6 7 8 9 0 2 4 1 3 1 2 3 4 5 6 7 8 9 0 2 4 1 3 EN55 Changing Remote Control Code 2 VIDEO (MONO)L—AUDIO—RS VIDEO S-VHS ET FFREW POWER REC PAUSE STOP/EJECT PLA – + CH– /+ PUSH / TURN 24HR QUICK PROGRAM REC LINK A.DUB INSERT 1 –1, 3 1 –2 1 –3 This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals. When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately. 1 1 Set remote control code for Remote 1 Press and hold A/B. 2 Press the Number key “2”. 3 Press OK, and release A/B. . The Remote now can transmit B code control signals. 2 2 Check remote control code for VCR Press and hold 3 on the VCR for more than 5 seconds while the VCR is turned off. The code currently set appears on the display panel. 3 3 Change code for VCR Press any key on the Remote. . The VCR now responds to B code control signals. . To set the Remote and the VCR back to A code control signals, repeat the same procedure as shown above except pressing the Number key “1” in step 2 of 1. To control two VCRs with the same Remote You can control two JVC VCRs by switching the remote control code for the Remote between A and B ( step 1), keeping two VCRs to different control codes. . Press the Number key “1” for A code control signals and the Number key “2” for B code control signals. (To change only the remote control code for the Remote, DO NOT perform steps 2 and 3 .) (Ex.) To set Remote to B code: MBR SET A/B 2 OK3 Release Hold Press in succession down TROUBLESHOOTING 56 EN Before requesting service, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your VCR off for repair. POWER SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The power will not come on. . The AC power cord is disconnected. Connect the AC power cord. . Child lock is on. Turn off child lock function ( pg. 45). 2. The clock works, but the VCR’s . The VCR is in the timer recording Press TIMER to disengage. power will not come on. standby mode with “AUTO TIMER” set to “OFF” ( pg. 40). . The child lock function is activated. Press and hold POWER for more than 10 seconds to release the child lock function ( pg. 45). 3. The Remote will not function. . The batteries are discharged. Replace batteries. . Timer is on. Press TIMER button on the remote. . Remote control A/B code is wrong. Reset A/B code ( pg. 55). TAPE TRANSPORT SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION 1. The cassette gets stuck partway . The cassette was inserted incorrectly. Make sure the cassette’s window is during loading, and is ejected. facing up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Then insert the cassette. PLAYBACK SYMPTOM CORRECTIVE ACTION POSSIBLE CAUSE 1. The tape is running but the picture Select channel 3 or 4 on the TV. will not appear. . If the RF connection ( pg. 7) is used to view the picture, the channel on the TV is set incorrectly. Select the AV mode on the TV. used to view the picture, the TV receiver is set to the wrong mode. . If the AV connection ( pg. 7) is 2. Breaks are noticeable in Hi-Fi . Automatic tracking is engaged. Disengage auto tracking and adjust sound track. the tracking manually ( pg. 23)...