




|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
242). The display changes as follows when you press DATA CODE on the Remote Commander: date/time ——— no indicator Various settings Various settings are your camcorder's information when you have recorded. In the recording mode, the various settings will not be displayed. When you use the data code function, bars (........) appear if: - A blank portion of the tape is being played back. - The tape is unreadable due to tape damage or noise. - The tape was recorded by a camcorder without the date and time set. Data code The data code is displayed on the TV screen if you connect your camcorder to the TV. Remaining battery time indicator during playback The indicator shows the approximate continuous playback time. The indicator may not be correct, depending on the conditions in which you are playing back. When you close the LCD panel and open it again, it takes about one minute for the correct remaining battery time to be displayed. Various settings/ Различные установки [a] [b] [c] [d] [e] [f] [g] [a] Счетчик ленты [b] Индикатор выключения устойчивой съемки [c] Индикатор режима экспозиции [d] Индикатор баланса белого [e] Индикатор усиления [f] Индикатор скорости затвора [g] Величина диафрагмы Для того, чтобы не отображались различные установки Установите опцию DATA CODE в положение DATE в установках меню (стр. 251). При нажатии кнопки DATA CODE на пульте дистанционного управления индикация будет изменяться следующим образом: дата/время -у без индикации Различные установки Различные установки представляют собой информацию о Вашей видеокамере при выполнении записи. В режиме записи различные установки отображаться не будут. Если Вы используете функцию кода данных, то появятся полосы (........), если: - Воспроизводится незаписанный участок на ленте. -Лента является нечитаемой из-за повреждения или помех. -Запись на ленту была выполнена видеокамерой без установки даты и времени. Код данных Если Вы подсоедините Вашу видеокамеру к телевизору, код данных появится на экране телевизора. Индикатор оставшегося времени заряда батарейного блока во время воспроизведения Этот индикатор показывает приблизительное время непрерывного воспроизведения. Индикатор может быть неточным в зависимости от условий, в которых Вы выполняете воспроизведение. Когда Вы закрываете панель ЖКД и открываете её снова, требуется около одной минуты для правильного отображения оставшегося времени заряда батарейного блока. 53 Playback - Basics Воспроизведение - Основные положения Playing back a tape Воспроизведение ленты Various playback modes To operate video control buttons, set the POWER switch to PLAYER*1)/VCR*2). *1) DCR-TRV16E/TRV18E/TRV24E only *2) DCR-TRV25E/TRV27E/TRV116E/TRV118E only To play back pause (view a still image) Press II during playback. To resume normal playback, press N or I . To advance the tape Press ^M in the stop mode. To resume normal playback, press N. To rewind the tape Press m in the stop mode. To resume normal playback, press N. To change the playback direction Press < on the Remote Commander during playback to reverse the playback direction. To resume normal playback, press N. To locate a scene monitoring the picture (picture search) Keep pressing or ^M during playback. To resume normal playback, release the button. To monitor high-speed pictures while advancing or rewinding the tape (skip scan) Keep pressing while rewinding or ^M while advancing the tape. To resume rewinding or advancing, release the button. To view the picture at slow speed (slow playback) Press y on the Remote Commander during playback. For slow playback in the reverse direction, press <, then press y on the Remote Commander. To resume normal playback, press N. 54 Различные режимы воспроизведения Для использования кнопок видеоконтроля установите переключатель POWER в положение PLAYER*1)/VCR*2). *1) Тол...
Эта инструкция также подходит к моделям:Видеокамеры - DCR-TRV116E (8.09 mb)
Видеокамеры - DCR-TRV118E (8.09 mb)