Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Focusing may become unstable during zooming. In this case, set the zoom while in Record- Standby, lock the focus by using the manual focus (. pg. 28), then zoom in or out in Record mode. . Zooming is possible to a maximum of 800X, or it can be switched to 32X magnification using the optical zoom. (. pg. 24) . Zoom magnification of over 32X is done through digital image processing, and is therefore called Digital Zoom. . During Digital Zoom, the quality of image may suffer. . Macro shooting (as close as approx. 5 cm to the subject) is possible when the Power Zoom Lever is set all the way to “W”. Also see “TELE MACRO” in FUNCTION Menu on page 24. . When shooting a subject close to the lens, zoom out first. If zoomed-in in the auto focus mode, the camcorder may automatically zoom out depending on the distance between the camcorder and the subject. This will not occur when “TELE MACRO” is set to “ON”. (. pg. 24) Journalistic Shooting In some situations, different shooting angles may provide more dramatic results. Hold the camcorder in the desired position and tilt the LCD monitor in the most convenient direction. It can rotate 270° (90° downward, 180° upward). Time Code During recording, a time code is recorded on the tape. This code is to confirm the location of the recorded scene on the tape during playback. Display Minutes Seconds Frames* (25 frames = 1 second) 12:34:24 * Frames are not displayed during recording. If recording starts from a blank portion, the time code begins counting from “00:00:00” (minute:second:frame). If recording starts from the end of a previously recorded scene, the time code continues from the last time code number. If during recording a blank portion is left partway through the tape, the time code is interrupted. When recording is resumed, the time code starts counting up again from “00:00:00”. This means the camcorder may record the same time codes as those existing in a previously recorded scene. To prevent this, perform Recording From The Middle Of A Tape (. pg. 20) in the following cases; . When shooting again after playing back a recorded tape. . When power shuts off during shooting. . When a tape is removed and re-inserted during shooting. . When shooting using a partially recorded tape. . When shooting on a blank portion located partway through the tape. . When shooting again after shooting a scene then opening/closing the cassette holder cover. VIDEO RECORDING & PLAYBACK CONTINUED ON NEXT PAGE VIDEO RECORDING 20 EN NOTES: . The time code cannot be reset. . During fast-forwarding and rewinding, the time code indication does not move smoothly. . The time code is displayed only when “TIME CODE” is set to “ON”. (. pg. 25) Quick Review Enables to check the end of the last recording. 1) Press QUICK REVIEW during the Recording-Standby mode. 2) Tape is rewound for about several seconds and played back automatically, then pauses in the Recording-Standby mode for the next shot. . Distortion may occur at start of playback. This is normal. Recording From The Middle Of A Tape 1) Play back a tape or use Blank Search (. pg. 21) to find the spot at which you want to start recording, then engage the Still Playback mode. (. pg. 21) 2) Set the Power Switch to “REC” while pressing down the Lock Button located on the switch, then start recording. VIDEO PLAYBACK EN 21 Normal Playback 5 VOL. +/– 3Speaker Lock Button MENU 4/98 1 Load a cassette. (. pg. 17) 2 Set the Power Switch to “PLAY” while pressing down the Lock Button located on the switch. 3 To start playback, press 4/9. 4 To stop playback, press 8. . During Stop mode, press 3 to rewind, or 5 to fast-forward the tape. To control the speaker volume Slide the Power Zoom Lever (VOL. +/–) towards “+” to turn up the volume, or towards “–” to turn down the volume. NOTES: . The playback picture can be viewed in the LCD monitor, viewfinder or on a connected TV. (. pg. 22) . If Stop mode continues for 5 minutes when power is supplied from a battery, the camcorder shuts off automatically. To turn on again, set the Power Switch to “OFF”, then to “PLAY”. . When a cable is connected to the AV connector, the sound is not heard from the speaker. Still Playback Pauses during video playback. 1) Press 4/9 during playback. 2) To resume normal playback, press 4/9 again. . If still playback continues for more than about 3 minutes, the camcorder’s Stop mode is automatically engaged. Shuttle Search Allows high-speed search in either direction during video playback. 1) During playback, press 5 for forward search, or 3 for reverse search. 2) To resume normal playback, press 4/9. . During playback, press and hold 5or 3. The search continues as long as you hold the button. Once you release the button, normal playback resumes. . A slight mosaic effect appears on the display during Shuttle Search. This is not a malfunction. ATTENTION: During Shuttle Search, parts of the picture may not be clearly visible, particularly on the left side of the screen. Blank Search Helps ...