Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
CHARGE Lamp flashes, then stays lit when charging is complete. ^ Attach fully charged Battery (page 9). 2 Slide TAPE EJECT to open door. 3 Insert cassette (page 11). 4 Press here to Protection Film close door. Note: • Remove the Protection Film before use. Camera Recording See page 17. Press LCD-OPEN to unlock the LCD monitor. Swing it fully open and adjust the angle. Set POWER to CAMERA. Press RECORD/PAUSE to start recording. Press RECORD/PAUSE again to pause recording. Playback using the LCD Monitor See page 20. Press LCD-OPEN to unlock the LCD monitor. Swing it fully open and adjust the angle (see above). 3 Press REWIND/SEARCH to rewind tape. 4 Press PLAY to start playback. 5 Press STOP to stop playback. 8 For assistance, please call: 1-800-211-PANA(7262) or send e-mail to : consumerproducts@panasonic.com Supplying Power Charging the Battery Pack Charge Battery Pack fully before use. 1 Plug in AC Adaptor. POWER Lamp lights. ^ Insert Battery. © Align left side of Battery with left edge of AC Adaptor. © Press Battery down and slide in direction | of arrow. The CHARGE Lamp flashes, then stays lit when charging is complete. O Remove Battery. Slide Battery to the left and lift off. Note: • Charging takes about 1 hour. • While the DC Power Cable (supplied) is connected to the AC Adaptor, the Battery cannot be charged. • After charging 5 times, use Battery Refresh feature as explained below. • Battery life gradually decreases after repeated use and recharging. If operation time becomes very short even after a sufficient charge, discard Battery properly (page 10). Using the Battery Pack A fully charged Battery provides a maximum of about 1 hour 10 minutes of continuous use (LCD monitor off) or about 55 minutes (LCD monitor on). Actual time may vary due to operating conditions. Using the Built-in Light decreases operating time. i Attach Battery. 0 Insert top of Battery into top of mounting surface. © Press and snap into place. B Remove Battery. Slide BATTERY RELEASE and remove Battery. Battery Refresh This feature completely discharges Battery before recharging begins. Use after every 5 charges for optimum Battery performance. To use battery refresh, insert Battery on AC Adaptor (see steps 1 ~2 above), then press BATTERY REFRESH. 3hts, then goes out when Battery charging will then The REFRESH Lamp I discharge is complete, start automatically. If BATTERY REFRESH is pressed by mistake, remove Battery from AC Adaptor and reinsert it for normal charging. Note: • Charging takes about 5 hours when Battery Refresh is used. • Battery will not operate in extremely high temperatures. Getting Started Supplying Power Battery Care Caution: • Charge only with specified charger. • Battery can be charged within a temperature range of 10°C (50 °F) and 35 °C (95 °F). • Battery is normally warm after charging or just after use. • Do not use an insufficiently charged or worn-out Battery. Safety precautions: • Do not get Battery near, or dispose of in, fire. • Do not directly connect (short circuit) the positive (+) and negative (-) terminals. • Never attempt to disassemble or reassemble Battery. To avoid Battery damage: • Do not drop or jar Battery. • Use Battery with specified units only. • If Battery is used in extremely high temperatures, a safety device will automatically prevent operation. To prolong Battery life: • While not in use, remove Battery from the Camcorder and AC Adaptor, and store in a cool, dark, dry place. • Keep Battery terminals clean. AC Adaptor DC OUT Connector Connect AC Adaptor DC OUT to Camcorder DC IN with supplied DC Power Cable. Plug in AC Adaptor. •WER Lamp lights. Note: • While the DC Power Cable (supplied) is connected to the AC Adaptor, the Battery cannot be charged. • When not in use, unplug AC Adaptor from AC outlet. (Adaptor uses 1.2 W of electricity while plugged in.) ■ CAUTION:- This unit will operate on 110/120/220/240 V AC 50/60 Hz. An AC plug adaptor may be required for voltages other than 120 V AC. Please contact either a local or foreign electrical parts distributor for assistance in selecting an alternate AC plug. We recommend using the accessory power plug adaptor (VJSS0070) in an area which has special AC outlets. Car Battery Cord (Optional) Car Battery Cord (optional) Cigarette Lighter Socket (12 V) Cigarette Lighter Plug 1 Connect PV-C16 Car Battery Cord (optional) to Camcorder DC IN. ^ (A) Start engine first. (§) Plug Car Battery Cord into Cigarette lighter socket. • If Car Battery cord fuse needs replacing, use exact current rating (in amps). Note: • This cord only works in vehicles equipped with DC 12 V (negative ground) battery. Check with your car/truck dealer. Use only specified car battery cord. • To avoid blowing the car battery cord fuse, do step 2 in the proper order. • Running vehicles must be well ventilated. • When not in use, disconnect cigarette lighter plug. • For p...