Оценок - 2, средний балл: 5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
1 Connect the AC cable to the AC adaptor and the AC jack. 2 Put the battery on the battery mount by aligning the mark, and then securely plug it in. . Charging lamp Lights up: Charging Goes off: Charging completed Flashing: The battery is over discharged (discharged excessively). In a while, the lamp will light up and normal charging will start. When the battery temperature is excessively high or low, the [CHARGE] lamp flashes and the charging time will be longer than normal. LSQT0860 . Connecting to the AC outlet 1 1 Connect the AC cable to the AC adaptor and the AC jack. 2 Connect the DC cable to the AC adaptor. 3 Connect the DC cable to this product. .The output plug of the AC cable is not completely connected to the AC adaptor jack. As shown in 1, there is a gap. .Do not use the power cord for other equipment since the power cord is exclusively designed for this Camcorder. Do not use the power cord from other equipment for this Camcorder. . Fitting the battery Push the battery against the battery holder and slide it until it clicks. . Removing the battery While pushing the [PUSH BATT] button, slide the battery (or the DC input lead) to remove it. PUSH BATT .Hold the battery with your hand so it does not fall. Before using Charging time and recordable time The times shown in the table below show the times at a temperature of 68oF (25oC) and a humidity of 60%. This is just a guide. If the temperature is higher or lower than the specified value, the charging time will become longer. Supplied A 1 h. 40 min. battery/ CGR-DU06 (7.2 V/ 640 mAh) B 1 h. 25 min. (1 h. 20 min.) CGA-DU12A 2 h. 25 min. (7.2 V/ 1150 mAh) B 2 h. 40 min. (2 h. 25 min.) CGA-DU21A 3 h. 55 min. (7.2 V/ 2040 mAh) B 4 h. 30 min. (4 h. 15 min.) A Charging time B Maximum continuously recordable time “1h. 10 min.” indicates 1 hour 10 minutes. .The battery CGR-DU06 is supplied. .The times shown in the table are rough estimates. The times indicate the recordable time when the viewfinder is used. The times in parentheses indicate the recordable time when the LCD monitor is used. .We recommend the Battery Pack CGA-DU12 and CGA-DU21 for long recording time (2 hour or more for continuous recording, 1 hour or more for intermittent recording). .The recordable time will become shorter in the following cases: .When you use both the viewfinder and the LCD monitor simultaneously while rotating the LCD monitor frontward to record yourself, 0 Lux MagicPix function, etc. .When you use this Camcorder with the LCD monitor lit up by pressing the [POWER LCD] button. .The batteries heat up after use or charging. The Camcorder being used will also heat up. This is normal. .Along with the reduction of the battery capacity, the display will change: r # s # t # u # v. If the battery discharges, then u (v) will flash. Inserting/removing a cassette 1 Slide the [OPEN/EJECT] lever and open the cassette cover. OPEN/ EJECT .When the cover is fully opened, the cassette holder will come out. 2 After the cassette holder is opened, insert/ remove the cassette. .When inserting a cassette, orient it as shown in the figure, and then securely insert it as far as it goes. .When removing, pull it straight out. 3 Push the [PUSH] mark 1 in order to close the cassette holder. 1 PUSH 4 Only after the cassette holder is completely housed, close the cassette cover. .After using, make sure to rewind the cassette completely, remove it, and put it in a case. Store the case in an upright position. (-62-) .When condensation is formed on the lens or the main unit of the Camcorder, even if no condensation alarm is indicated, condensation may have formed on the heads or the cassette tape. Do not open the cassette cover. (-59-) . When the cassette holder does not come out .Close the cassette cover completely, and then open it again completely. .Check if the battery has run down. . When the cassette holder cannot be housed .Set the [OFF/ON] switch to [OFF], then to [ON] again. .Check if the battery has run down. LSQT0860 Before using . Inserting/removing the cassette .When the cassette holder is in motion, do not touch anything except the [PUSH] mark. .When inserting a previously recorded cassette, use the blank search function to find the position where you want to continue recording. If you overwrite-record on a previously recorded cassette, be sure to find the position where you want to continue recording. .Close the cassette cover tightly. .When closing the cassette cover, do not get anything, such as a cable, caught in the cover. . Accidental erasure prevention If the accidental erasure prevention slider 1 of a cassette is opened (slide in the direction of the [SAVE] arrow), the cassette cannot be recorded. When recording, close the accidental erasure prevention slider of the cassette (slide in the direction of the [REC] arrow). R E C SAVE 1 Inserting/removing a card Before inserting/removing a card, be sure to turn the power [OFF]. .If the card is inserted or removed with the power turned on,...