Оценок - 3, средний балл: 3.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
When the controller is not in use, attach the clip to the Grip Belt for convenience. This controller makes it easier for left-handed users to use the Palmcorder. (85) (80) (81) (82) (83) (84) (80) Microphone [MIC] -26( 81) Recording Start/Stop Button [REC] (82) Zoom Lever [W/T] .Zoom speed changes in 2 stages. (83) Photoshot Button [PHOTO SHOT] (84) Microphone Switch Button [TALK] -26. When the Magic Wire Remote Control with Narration Mic is connected to [REMOTE] Jack and the [TALK] Button is pressed, the narration microphone is activated and the built-in microphone on the Palmcorder is deactivated. (85) Clip -14 ZOOM INDEX INDEX SELECT STORE STOP KL. OSD DISPLAY V/REW STILL ADV OFF/ON P.B.DIGITAL DATE/ TIME RESET TITLE T W sVOL r.RECMULTI/ P-IN-P PHOTO SHOT START/ STOP A.DUB PLAY PAUSE FF/WSTILL ADV ENTER 615;EDVAR. SEARCH MENU P.B. ZOOM Before Use .Insert the plug securely into the [REMOTE] Jack as far as it will go. A loose connection will affect normal operation. The Remote Controller . Inserting a Button-type Battery Before using the Remote Controller, insert the supplied button-type battery. 1 While pressing the Lock Button 1, pull out the Battery Holder. 1 2 Insert the button-type battery with the (i) marking facing upwards. 3 Insert the Battery Holder into the Remote Controller. .When the button-type battery is exhausted, replace it with a new CR2025 battery. (A battery is normally expected to last about 1 year. However, it depends on operation frequency.) .Make sure to match the poles correctly when inserting the battery. Warning Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions. Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212°F (100°C) or incinerate. Keep the Button-Type battery out of the reach of children. Never put Button-Type battery in mouth. If swallowed, call your doctor. Replace battery with Panasonic PART NO. CR2025 only. Use of another battery may present a risk of fire or explosion. Caution: Battery may explode if mistreated. Dispose of used battery promptly. Keep away from children. Do not recharge, disassemble or dispose of in fire. . Using the Remote Controller 1 Direct the Remote Controller at the Remote Control Sensor (33) of the Palmcorder and press an appropriate button. 15 . 15° 15 . (33) 15° .Distance from the Palmcorder: Within approximately 15 feet (5 meters) .Angle: Approximately 15o in the vertical and horizontal directions from the central axis .The above operating ranges are for indoor use. Outdoors or under strong light, the Palmcorder may not operate properly even within the above ranges. .Within a 3 feet (1 meter) range, you can also use the Remote Controller on the LCD Monitor side of the Palmcorder. Selecting Remote Controller Modes When 2 Palmcorders are used simultaneously, they can be operated individually by selecting different Remote Controller Modes. .If the Remote Controller Mode of the Palmcorder and that of the Remote Controller do not match, [REMOTE] Indication is displayed. Setup on the Palmcorder: Set [REMOTE] on the [INITIAL] Sub-Menu to the desired Remote Controller Mode. (-22-) Setup on the Remote Controller: INDEX INDEX SELECT STOP KL. STILL ADV PAUSE STILL ADV 615;EDP.B. ZOOM 2 1 [VCR1]: Press the [D] Button and [.] Button simultaneously. 1 [VCR2]: Press the [E] Button and [.] Button simultaneously. 2 .When the battery in the Remote Controller is replaced, the mode is automatically reset to [VCR1] Mode. -15 Before Use Power Supply . Using the AC Adaptor 1 1 Connect the DC Cable to the Palmcorder. 2 Connect the DC Cable to the AC Adaptor. 3 Connect the AC Cable to the AC Adaptor and the AC Jack. .The AC Cable’s outlet plug does not fit entirely into the AC Adaptor jack. A gap will remain as shown 1. .Before connecting or disconnecting the power supply, set the [OFF/ON] Switch on the Palmcorder to [OFF] and make sure that [POWER] Lamp is not lit. . Using the Battery Before use, fully charge the Battery. .We recommend using a Panasonic Battery. .We cannot guarantee the quality of this Palmcorder when batteries from other companies are used. 1 Attach the Battery to the AC Adaptor and charge it. .Since the Battery will not be charged when the DC Cable is connected to the AC Adaptor, disconnect it from the AC Adaptor. .The [CHARGE] Lamp lights up, and charging starts. .When the [CHARGE] Lamp goes off, charging is completed. .When the battery is completely discharged, the [CHARGE] lamp blinks at first, but the battery is charged normally. When the temperature of the battery is too high or low, the [CHARGE] lamp blinks and the charging time becomes longer than usual. 2 Attach the charged Battery to the Palmcorder. Disconnecting the Power Source Set the [OFF/ON] Switch (46) to [OFF] and, while pressing the [PUSH BATT] Button (51), slide the Battery or DC Cable upward to d...