Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Set the POWER switch to VCR. 2Press REWIND/SEARCH to rewind the tape. 5 Press PLAY to start playback. 4press STOP to stop playback. Supplying Power Charge the Battery Pack Charge the Battery Pack fully before operation. POWER Lamp CHARGE Lamp Note: After recharging the Battery Pack about 5 times, use the BATTERY REFRESH feature as explained on page 8. Use the Battery Pack Plug in the AC Adaptor. POWER Lamp lights up. Insert the Battery ® Align the right side of the Battery with the line on the AC Adaptor. Press down on the Battery and then slide it in the direction of the arrow. CHARGE Lamp lights up. It goes out when charging is done (about one and a half hours). Remove the Battery Slide the Battery out and then lift up. The useful operation time of the Battery will gradually decrease after repeated use and recharging. The Battery is no longer serviceable if the operation time is very short, even after a sufficient charge. With a fully charged Battery Pack, you will have a maximum of about one and a half hours of continuous use. (If the Built-in Light is used, battery operating time decreases.) Attach the Battery ® Align the Battery with the top of the mounting surface. ® Press it into place until it locks with a click. Remove the Battery While sliding the BATTERY RELEASE button, remove the Battery. Getting Started Supplying Power Battery Refresh Feature This feature completely discharges the Battery before recharging begins. To maintain your battery’s operating capacity, use the refresh feature after about every five charges. CHARGE Lamp Plug in AC Adaptor. ONLY FOR U.S.A. Place the Battery into the AC Adaptor. Press the BATTERY REFRESH button. The CHARGE Lamp will flash when discharging begins and stop ftashing when fully discharged. POWER Lamp will stay lit when fully charged. dt Remove the Battery Should you accidentally press the BATTERY REFRESH button, remove Battery and then re-insert it to begin charging. It takes about seven and a half hours when both Battery Refresh and charging are performed. ATTENTION: The product that you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. Battery Care Caution: • Charge only with specified charger. • The Battery can be charged within a temperature range of 32° F (0° C) and 104° F (40° C). • The Battery may be warm after charging or just after use. This is normal. • Do not use an insufficiently charged or worn out Battery. Safety precautions: • Do not get the Battery near, or dispose of in fire. • Do not directly connect (short circuit) the positive {+) and negative (-) terminals. • Never attempt to disassemble or reassemble the Battery. 8 To avoid damage to the Battery: • Do not drop or jar the Battery. • Use the Battery with specified units only. • If the Battery is used in extremely high temperatures, a safety device will automatically prevent operation. To insure longer battery life: • While not in use, remove Battery from the Palmcorder and AC Adaptor and store in a cool, dark, dry place. • Keep the Battery terminals clean. Supplying Power AC Adaptor — DC Power Cable POWER Lamp DC IN Connector VCR DC OUT Connector Connect the VCR DC OUT on the AC Adaptor to the DC IN on the Palmcorder with the DC Power Cable (supplied). Plug in the AC Adaptor. The POWER Lamp will light up. Note: • AC Adaptor can not be used to power the Palmcorder while charging the Battery. • While not in use, unplug the AC Adaptor from the AC outlet. (AC Adaptor consumes 1.2W of electric power if it is plugged into an AC outlet even when not in use.) Car Battery Cord (Optional) DC IN Connector Cigarette Lighter Socket (12V) Car Battery Cord (optional) Cigarette Lighter Plug A. Connect a PV-C16 Car Battery Cord (optional) to the DC IN of the Palmcorder. 2Start your car engine and then insert the Car Battery Cord plug into your cigarette lighter socket. • There is a fuse located in the lighter plug end of the cord. Should fuse replacement be necessary use the exact current rating (in amps). Note: • This cord can only be used in vehicles equipped with DC 12V (negative ground) batteries. Use only the specified car battery cord. If you are not sure check with your local car/truck dealer as to what type of DC battery ground you have in your vehicle. • Be sure to start your car engine before inserting the cigarette lighter plug of the Car Battery Cord into the lighter socket; otherwise, the cigarette lighter plug fuse may burn out. • Because the car is running while your Palmcorder is in operation, make sure you’re in a well ventilated area. • Disconnect the cigarette lighter plug when your Palmcorder is not being used. Getting Star...