Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Please delete unneeded files or use an SD card with space on it. Card is protected The write protection switch on the SD card is in the LOCK position. Please unlock the write protect switch. (l40) Others Troubleshooting . It is not a malfunction in following cases Object seems to be . Object seems to be warped slightly when the warped. object moves across the image very fast, but this is because the unit is using MOS for the image sensor. This is not a malfunction. VQT4F46 173 White round spots like soap bubbles appear on the recorded picture. . If you take a picture with the flash in a dark place or indoors, white round spots may appear on the picture caused by the flash reflecting of particles of dust in the air. This is not a malfunction. A characteristic of this is that the number of round spots and their position differ in every picture. Why does the displayed image contain some red, blue and green dots, or why are black spots visible. . Condition due to the LCD monitor characteristics. Not a malfunction. Spots only appear in the LCD monitor and will not be recorded with the images. Power Problem Check points This unit cannot be turned on. This unit does not stay on long enough. Battery runs down quickly. . Recharge the battery pack or connect the AC adaptor. (l34) . In cold places, the battery using time becomes shorter. . It is possible to insert the battery incorrectly, so please pay particular attention when inserting that it is correctly oriented. The battery does not charge. The battery does not stop charging. . Check that the plug portion of the AC adaptor is not loose or misaligned. 174 VQT4F46 Power Problem Check points This unit is turned off automatically. . To prevent battery consumption caused by forgetting to turn the unit off etc., the economy mode function works to send the unit into sleep mode if the unit has been on for approximately 5 minutes (default setting) without an operation being performed. When the unit is in sleep mode, you can turn on the unit by pressing any of the buttons on the unit. . If the unit turns off when you turn off the power to the TV using the TV remote control, the VIERA Link is at work. If you are not using the VIERA Link, set [VIERA Link] to [OFF]. (l138) This unit cannot be operated though it is turned on. This unit does not operate normally. . Remove the battery or AC adaptor, wait about 1 minute and then reconnect the battery or AC adaptor. Then about 1 minute later, turn on the unit again. (Conducting the above operation while the media is being accessed may damage the data on the media.) . If normal operation is still not restored, detach the power connected, and contact consumer support. (l207, 208, 209) A blinking high temperature warning icon is shown, and the unit does not turn on. . The battery temperature or unit internal temperature (excluding battery) rises. Wait for the temperature to drop before using the unit again. VQT4F46 175 Power Problem Check points “ERROR OCCURRED. PLEASE TURN UNIT OFF, THEN TURN ON AGAIN.” is displayed. . Check each of the following items. jRemove the SD card from the device and reinsert. jRemove the battery and then put it in again. jChange the SD card and check. . If a message is still displayed after checking the above, detach the power connected, contact consumer support. (l207, 208, 209) Indication Problem Check points The battery capacity indication or the elapsed time indication is not shown. . [DISPLAY] is [OFF]. (l71) Status indicator Problem Check points The status indicator is flashing red. . During battery charging, the status indicator flashes red with a period of approximately 2 seconds (approximately 1 second on, 1 second off). When charging ends, the status indicator turns off. This is not a malfunction. 176 VQT4F46 Recording Problem Check points The high temperature warning icon is displayed and recording is not possible. . The battery temperature or unit internal temperature (excluding battery) rises. Wait for the temperature to drop before using the unit again. When recording still pictures, the angle of view of the image displayed on the LCD monitor changes. . The field of view of the image displayed on the LCD monitor differs for motion picture recording and still picture recording. At time of purchase, the recording standby screen shows video view. Press the button halfway to change to photo view. To change the angle of view of the recording standby screen to photo view, set [PHOTO VIEW] to The unit arbitrarily stops recording. . U r motion p . T hortened due t a writing s eletion. U or built-in memory Image not in focus . C monitor. A en on agai [F ] is (MANUAL), do the above, then reconfigure the manual focus. There is noise in the recording image. . When the [ISO] setting is too high, noise may appear in the recorded images. Please lower the ISO sensitivity setting. (l100) VQT4F46 177 Recording Problem Check points Color balance of images is strange when recording in a place such as a gymnasiu...