Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
You set up the delayed recording using the on-screen Easy Guide System. 1. Press GUIDE, then press 1 to select VCR PLUS RECORDING and bring up this screen: 2. Use the number buttons to enter the PlusCode of the program you want to record. This code can be up to eight digits. If you enter a wrong digit, press CLEAR and enter the correct one. 3. If you accidentally enter a nonexistent PlusCode, the VCR gives you an error message that disappears from the screen in about 10 seconds. 4. If you have entered the correct PlusCode, press GUIDE to store the PlusCode in the VCR's memory. This brings up another screen: Advanced Operations 5. Press number buttons 1, 2, or 3 to select ONE TIME, DAILY, or WEEKLY RECORDING. Important: Programming does not take effect unless you select one of these options. 6. When the next screen comes up, choose between standard or extended tape speed by pressing the 5 button. This is also a good time to check the channel number-- it should be the one on which you usually watch the program at home. (If not, you need to check your VCR Plus+ channel setup.) 7. Review the screen to be sure everything is set as you want, then press GUIDE to complete your programming or continue with additional programs. When you have set up all the timed recordings you want: Don't forget to load a videocassette (with the safety tab still attached) to record on. If using a cable box the VCR can control, turn on the cable box before the time the recording is to begin. If using a cable box the VCR cannot control, turn on the cable box and tune it to the channel you want to record before the time the recording is to begin. Important: Your timed recording settings take effect when you turn off the power on the VCR. Caution on the VCR Plus+ recordingAfter entering a VCR Plus + number, check the information displayed with the "PROGRAM REVIEW", if there is (are) any unnecessary program(s), please cancel or correct it (them). Advanced Operations This section explains how to use the VCR's remote control to operate your TV. It also shows you how to hook up a cable box and how to connect a stereo or a second VCR Advanced Operations for a complete home entertainment system. Controlling Your TV with the VCR's Remote Compatibility The remote control is designed to be compatible with many televisions and cable converters, but will not work with every one made. If your TV or cable box does not respond the way it should when you program it as explained below, this remote may be incapable of operating it. Once you have programmed the remote, you won't have to do it again until you change the batteries. This Hitachi remote control can be used with your TV as well as the VCR, as long as your TV comes with a remote control. This feature comes in handy--you don't have to juggle two remotes. The remote control is compatible with the fifteen makers of TV's listed below--but don't be alarmed if yours is not on our list. You may still be able to program the remote for your TV. Every TV that comes with a remote control is set up to detect certain infrared signals. You need to program the VCR's remote control to send signals that your TV will recognize and respond to. Here's what to do: Programming the Remote Control Turn the television on (any channel is okay). Aim the VCR's remote control at your TV set. Hold down the TV button (Not the VCR/TV button) while you press the number corresponding to your brand of television as shown in the chart (page 52). For example, if you have an RCA television, press TV and 0 at the same time. If this button combination sends a signal that matches your TV, the channel will change on the TV, and you'll know the remote is set to control the television. If that button combination does not change the TV channel, go through the whole list of button combinations one by one until you find one that does change your TV channel. Also, if your brand of TV is not listed in the chart, try all the number buttons. One of them may work for you. If the TV channel still doesn't change after going through all the button combinations listed, it is likely that you will not be able to program this remote control for your TV. TV Brands Press TV and This Number Hitachi 1 Zenith 2 Advanced Operations (Cable Box Hookups) Sony 3 Magnavox 4 Sanyo 5 Gold Star 1 6 Toshiba 7 Gold Star 2 8 Panasonic 2 9 RCA 0 Panasonic 1 CHANNEL (up arrow) Mitsubishi CHANNEL (down arrow) JVC 100/ENT Sharp 1 LAST CH Sharp 2 DISPLAY Controlling the TV Once programmed, the VCR's remote control is ready to control the TV. First press TV to change to the TV function mode, then press the button of the TV function that you want. For example, press TV and the CHANNEL up arrow, and the TV station will change to the next higher station. Press VCR to operate your VCR with the remote again. Be aware that not all of your TV's functions may work even though the remote control is correctly programmed. Advanced Operations (Cable Box Hookups) Hooking Up to ...