Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Press the button on the remote control to display the current zero value. Advance Tare Weight To input a known tare weight before weighing an item, press MR and the screen will display SHIFT. Press TARE, and the screen will display 000.00. To input the desired weight, scroll to the right by pressing the right arrow (TARE) button on the remote control until you come to the number that you would like to change. To increase the number from zero, press the left button ( ) button on the remote control. To decrease the number, press CLEAR on the remote control. When you are satisfied with the current number, press the M+ button to move to the left. To submit the tare amount, press MR and the TARE light will come on the scale, automatically deducting the imputed tare weight. The tare weight will stay the same until the scale is turned OFF. Clear Function To clear, press the CLEAR button and the screen will flash CLr. If you would like to approve the clear command, press the MR button and the screen will display 8.8.8.8.8, confirming the deletion. If you would like to cancel the clear command, press the CLEAR button again. The screen will display noCLr, canceling the deletion. Search Overload Times To review how many instances the scale has been overloaded, press the MR button and the screen will display SHIFT. Press the CLEAR button and the screen will display OL=XX, showing how many times the scale has exceeded its maximum capacity. Display Function To change the brightness of the display, press F1. Display brightness ranges from 1 (minimum light) to 5 (maximum light). The default display setting is 2. -8- Model T10007 300 Kg Digital Crane Scale Note: The remote control is a generic remote and may contain buttons that will not be used with this particular model. Should you lose the included remote control, the remote control functions cannot be completed. To obtain a replacement controller from Grizzly; call 1-800-523-4777. Reference Guide For quick references and questions about scale displays, use these reference charts for assistance. Display Action - - - - Wait signal Err10 Accumulated weight below capacity Err11 Accumulated times exceed (30+) Err12 Accumulated weight exced (999.99) CLr Delete weight? noCLr Cancel deletion 88888 Confirm deletion noACC No accumulated value SHIFt Weight conversion UX.XX Current battery voltage SCALE Enter weight adjustment SEtUP Enter parameter adjustment UAdJ Enter voltage adjustment -OL-Overload warning -Lb-Low battery warning End Parameter adjustment ready OFF Turn off Function Button ON OFF OFF/ Zero Tare TARE/ Hold HOLD Brightness F1 Display Action 8.8.8.8.8 661.4 U X.XX - - - - 0.0 Scale is ready for use U X.XX OFF Scale is OFF 0.0 Display reads 0, "Zero" LED is on 0.0 Display reads 0, Tare LED is on XXXX.X Weight is held, press HOLD to exit 1 through 5 1=lowest, 5=highet setting Function Button Display Button Lb/Kg Conversion MR SHIFT HOLD Battery Voltage MR SHIFT F1 Current Zero Value MR SHIFT / Advance Tare MR SHIFT TARE/ Overload Review MR SHIFT CLEAR Clear CLEAR CLR MR CLEAR . Action UN=O (weight in Kg, "lb" LED is off) UN=1 (weight in Lb, "lb" LED is on) U X.XX, press MR to exit XXXX.X Current zero value TARE to scroll right to increase number CLEAR to decrease number M+ to submit and scroll left MR to submit total, "TARE" LED is on OL=XX (Overload= XX times) 888.88 = confimation of clear noCLR = cancel clear . Model T10007 300 Kg Digital Crane Scale -9 SECTION 5: MAINTENANCE General Regularly check mounting hardware for cracks, unsafe wear, deformation, or warping. DO NOT attempt to fix the mounting harware! Discard and replace all damaged mounting hardware. Regularly check for loose pins, rings, screws, and safety latches. Tighten or replace any loose items. Damaged or loose parts may cause the load to fall and may result in serious injury. Always keep the scale in a hanging position to relieve strain on the load cell. Never leave a load or weighing equipment on the scale when not in use. This may cause excessive strain on the precision weighing device and may result in inaccurate readings and shorten the life of your scale. When recharging the scale battery, charge for at least 8 hours. Excessive charging will not damage the battery. Batteries must be recycled or disposed of properly. If your scale malfunctions permanently, do not attempt to fix it yourself. Contact a certified professional for any electrical or detailed calibration work. If the scale becomes dirty, clean the screen with a soft cloth using a mild window cleaner or detergent. Avoid using paper towels. DO NOT use solvents, chemicals or other corrosive materials to clean the scale. If the scale will not be used for a prolonged amount of time, remove the battery. Suspend the scale at all times and do not allow it to rest on the ground. ! Always DISCONNECT POWER before servicing, adjusting, or doing main- tenance to reduce the risk of acci- dental injury or electrocution. BATTERY MUST BE RECYCLED OR D...