When you contact us we need to know: • Your name • Address and post code • Telephone number • Clear and concise details of the fault • Name and model of the appliance* • E number* • This information can be found on the rating plate, which can be seen when the grease filters are removed. Customer Care For general enquiries concerning your AEG appliances, or for further information on AEG products, please contact our Customer Care Department at the address below or visit our website at Cu

electrical goods retailer. If the socket outlets are not suitable for the plug fitted t. the appliance, then the plug must be cut off and destroyed for safety reasons, an. an appropriate plug be fitted. When wiring the plug ensure that all strands of wire are securely retained in eac. terminal. Do not forget to tighten the mains lead clamp on the plug. Electrical connection. 230 V - using fixed power supply line with plug. 240 V - using fixed power supply line (Great Britain). Fuse ratin. 13 amp

keep bends in outlet hose to a minimu. . never install the hoses with an acute angle, they mus. always follow a gentle curve onl. . keep the hose as large as possible (120 mm O min.). l Failure to observe these basic rules will drastically reduc. the performance and increase the noise levels of th. extractor hood. Installation - Fig. . . lllll Put the template onto the wall (1) and drill two O12mm holes (2). . lllll Fit two hooks (3) on the drilled holes. . lllll Hang the hood on the hooks and a

The fan speed is set high enoug. for the task. The grease filter is clean. The kitchen is adequately vented t. allow the entry of fresh air. If set up for recirculation, check tha. the charcoal filter is still effective. If set up for extraction, check tha. the ducting and outlets are no. blocked. The cooker hood has switched of. The safety cut-out service has bee. during operation... tripped. Turn off the hob and then wait for th. device to reset. If after all these checks, the problem persists

• You will need original AEG carbon filter KLF 60/80 for this function (see Special Accessories). • In this version fumes are extracted to the outside via a hose. • In order to obtain the best performance the hose should have a diameter equal to the outlet hole. Filter Version • The air is filtered using a carbon filter and recirculated into the kitchen. • You will need an original AEG KLF60/80 activated carbon filter for the filtering function. (See Special Accessories). Description of the appl

• The upper part of the spice rack rear wall should be detachable (access for exhaust air hose or adjustment of furniture housing). Fig. 6a Fig. 6b Installing the fume extractor hood in the wall unit - extractor version (Filter version with carbon filter) • Apply the drilling template to the inside wall of the wall unit on the right and left sides, and mark out and predrill O 2 mm mounting holes as well as 2 x O 6 mm - 5 mm depth holes for the mounting claws (installation aids). • Unscrew the ve

• You will need an original AEG charcoal filter for the filtering function. (See Special Accessories). • Fix the deflector using 2 screws O 2,9x13 mm. Fig. 2. • Optionally, the position of the chimney elements can be changed. When using the hood in the filter version the chimney must be fixed at the top, with the air outlet grill at the side. Fig. 1 Fig. 2 5 Control Panel • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Tu

Repeat the process if necessary. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry. When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance. • Clean the inner housing using a hot detergent solution only (never use ca