Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
2. This water heater must be grounded. 3. Install or locate this water heater only in accordance with the provided installation instructions. 4. Use this water heater only for its intended use as described in this manual. 5. Contact a qualified electrician to have unit properly installed. 6. As with any appliance, close supervision is necessary when used by children. 7. Do not operate this water heater if it is not working properly or if it has been damaged or dropped. 8. This water heater should be serviced only by qualified service personnel. Contact a service facility for examination, repair or adjustment. 9. Failure to service the anode rod at least once a year could cause the tank to fail and leak. KEEP THESE INSTRUCTIONS AT HAND SAVE THESE INSTRUCTIONS Technical data MODEL GL 2.5 GL 4 GL 6+ Capacity gallons 2.5 4 6 Voltage Vac 110/120 for each model Power at 120 Vac Watts 1500 1500 1500 Maximum Water pressure psi 150 150 150 Weight Lbs 15.5 17.3 29.5 Amperage Amps 12.50 for each model Phases 1 1 1 WARNING The installer should review the contents of this manual with the owner upon completion of installation, and the manual should be left with the owner and placed in a location close to the installation. Temperature & pressure relief valve, 3/4 NPT male Temperature & pressure relief valve, 3/4 NPT male 3/4 NPT female tapping for relief valve 3/4 NPT female tapping 3/4 NPT female tapping 3/4 NPT female tapping for relief valve Hot water outlet 1/2 NPT male 3/4 NPT female tapping for relief valve FIG. 1/1 Temperature & pressure relief valve, 3/4 NPT male Cold water inlet 1/2 NPT male Temperature & pressure relief valve discharge line to drain COMPONENT PARTS OF GL 2.5 - GL 4 COMPONENT PARTS OF GL 6+ (Vertical installation) COMPONENT PARTS OF GL 6+ (Horizontal installation) FIG. 1/2 FIG. 1/3 Temperature & pressure relief valve discharge line to drain Hot water outlet 3/4 NPT male Hot water outlet 3/4 NPT male 3/4 NPT male plug 3/4 NPT male plug Temperature & pressure relief valve discharge line to drain Cold water inlet 3/4 NPT male Cold water inlet 3/4 NPT male Hot water outlet 1/2 NPT male 3/4 NPT female tapping for relief valve FIG. 1/1 Temperature & pressure relief valve, 3/4 NPT male Cold water inlet 1/2 NPT male Temperature & pressure relief valve discharge line to drain COMPONENT PARTS OF GL 2.5 - GL 4 COMPONENT PARTS OF GL 6+ (Vertical installation) COMPONENT PARTS OF GL 6+ (Horizontal installation) FIG. 1/2 FIG. 1/3 Temperature & pressure relief valve discharge line to drain Hot water outlet 3/4 NPT male Hot water outlet 3/4 NPT male 3/4 NPT male plug 3/4 NPT male plug Temperature & pressure relief valve discharge line to drain Cold water inlet 3/4 NPT male Cold water inlet 3/4 NPT male FIG. 2/1 DIMENSIONS FOR GL 2.5 - GL 4 GL 2.5 GL 4 14” 10 1/4” 12 1/4” 7 1/2” 3” 6” 3 1/2” 1” 14” 5 1/2” 3 3/4” 2 1/2” 1/2 NPT MALE FIG. 2/2 DIMENSIONS FOR GL 6+ (HORIZONTAL INSTALLATION) 14 1/2” 8 1/2” 4 1/2” 17 1/2” 17 1/2”11 1/2” 3/4 NPT MALE 3” FIG. 2/3 DIMENSIONS FOR GL 6+ (VERTICAL INSTALLATION) 14 1/2” 8 1/2” 4 1/2” 11 1/2” 17 1/2” 17 1/2” 1” 3/4 NPT MALE 2 1/2”6 1/2” General remarks CAUTION The manufacturer cannot be responsible for the damages caused by improper installation or by failure to follow instructions in this pamphlet. Comply with the installation instructions before completing electric connection. CAUTION The thermostat has been pre-set at the factory between 41°C (105° F) and 45° C (113° F). CAUTION Hydrogen gas can be produced in a hot water system served by this heater that has not been used for a long period of time (generally 2 weeks or more). Hydrogen gas is extremely flammable. To reduce the risk of injury under these conditions, it is recommended that the hot water faucet be opened for several minutes at the kitchen sink before using any electrical appliance connected to the hot water system. If hydrogen gas is present, there will probably be an unusual sound such as air escaping through the pipe as the water begins to flow. There should be no smoking or open flame near the faucet at this time. Installation instructions MODEL GL 6+ Wall mounting (only for vertical installation) Floor Mounting Wiring Pipe connections The GL 6+ water heater can be installed under the sink. Fasten the supplied mounting bracket to the wall. Use screws that are suitable for the wall material and the weight of the heater. Hang the water heater on the bracket. Tug down wards on the heater to ensure that both “fingers” of the bracket are seated in the mounting slots. Confirm water piping orientation before wall mounting. Heater can sit on floor. Confirm water piping orientation before locating on floor location. The GL6+ needs to be wired with 12 GA. wire to a minimum 20 amp/ maximum 20 amp branch circuit. (Remove cover plate V (fig. 3/4) using a thin screw-driver operating on point W (fig. 3/4). Unscrew the screw below and lift the cover C (fig. 3/4). When reassembling work in the opposite way being careful to i...
Эта инструкция также подходит к моделям:Вентиляторы - GL 2.5 (139.04 kb)
Вентиляторы - GL 6+ (139.04 kb)