Войти:
Оценок - 4, средний балл: 4 ( )

Инструкция по эксплуатации Dacor, модель PLHV36W7CC

Производитель: Dacor
Размер: 1.15 mb
Название файла: PLHV36W7CC_use-care.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


For serviceability,a mounting similar to the straight up discharge should be used. 6 Installation Wiring to Power Supply WARNING! ELECTRICAL GROUNDING INSTRUCTIONS THIS APPLIANCE IS FITTED WITH AN ELECTRICAL JUNCTION BOX WITH 3 WIRES, ONE OF WHICH (GREEN/YELLOW) SERVES TO GROUND THE APPLIANCE. TO PROTECT YOU AGAINST ELECTRIC SHOCK, THE GREEN AND YELLOW WIRE MUST BE CONNECTED TO THE GROUNDING WIRE IN YOUR HOME ELECTRICAL SYSTEM, AND IT MUST UNDER NO CIRCUMSTANCES BE CUT OR REMOVED. Warning: Turn off power circuit at the service panel before wiring this unit. 1. 120 V AC, 15 AMP branch circuit required. 2. Remove the junction box cover, unscrew the 4 screws that fix it to the body of the hood. 3. Install the conduit connector (1/2") in junction box. 4. Run 3 wires; black, white and green (wire gauge per code) in 1/2" conduit from service panel to junction box. 5. Connect black wire from service panel to black or red in junction box, white to white and green to green-yellow. 6. Close junction box cover, with its 4 screws. Check all light bulbs to make sure they are secure in their sockets. Turn power on in service panel. Check lights and blower operation per Care & Use section of this manual. Install filters. 7. Install duct cover as shown in Fig. 6. 8. Fit the filters , see Page 9. Rear discharge: A 90° elbow may be installed immediately above the hood. For serviceability, a mounting similar to the straight up discharge shown in Figure 4 should be used. Figure 6 7 Use anJ gare READ THE INSTRUCTIONS CAREFULLY BEFORE USING THE HOOD. Use anU gar'C For satisfactory use of your hood, become familiarwith the various functions of the hood as described below Suction power 2 LED, this led is ON when suction power 2 is selected. Suction power 3 LED, this led is ON when suction power 3 is selected. is ON when suction power I is selected. Intensive Suction power LED, this led is ON when the intensive suction power is selected. Figure 7 Light OFF button Light ON button Intensive Suction power button - this suction power will function for 10 mins. then the hood set again the preselected speed Grease Filter Saturation LED The Suction power 2 LED is marked with an F. This LED will flash to remind you when the grease filter needs to be cleaned after 40 hours use. Follow the instructions for cleaning filters in this booklet. Once the grease filters have been cleaned, reset the reminder by pressing Motor OFF button for about 3 seconds until you hear the signal (beep). Should the Suction power 3 LED starts to flash then push ON and power selection button and the Intensive Suction power button simultaneously for more than 3 seconds to stop flashes. Operating Instructions The blower should be turned on for about 5 minutes before cooking in order to establish air currents upward through the hood. Use the low speeds for normal use and the higher speeds for strong odors or fumes. Minimize cross drafts which will reduce the effectiveness of the hood. 8 Hood Cleaning Be sure lights are cool before cleaning the...

Эта инструкция также подходит к моделям:
Вентиляторы - PLHV36W7CC (1.15 mb)
Вентиляторы - PLHV36W7CC (1.15 mb)
Вентиляторы - PLHV36W7CC (1.15 mb)
Вентиляторы - PLHV36W7CC (1.15 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории