Оценок - , средний балл: ( )

Инструкция по эксплуатации Electrolux, модель MCH 662

Производитель: Electrolux
Размер: 360.97 kb
Название файла: d1b5bb98-f6bc-7604-61ff-ce9acc9dc8a9.pdf

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Ducting The ducting must be fire retardant 100mm (4”ins) in diameter and the length should be no more than: 3 metres with one 90° bend 2 metres with two 90° bends Bends of more than 90° will reduce the efficiency of the hood and reduce the airflow. Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions. 11 Clearance Height A clearance height of 650mm (25 1/2 ”) is required when installed above a built-in electric hob, or 700mm (27 1/2 ”) when installed above a built-in gas hob. A clearance height of 685mm (27”) is required when installed above a slot-in electric cooker, or 787mm (30 1/2 ”) when installed above a slot-in gas cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mm. If the height of the wall cabinet is less than 450mm, a gap of 50mm must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. Unpacking The fittings supplied to install this cooker hood can be found with the instruction book inside the packaging. The fixing kit comprises: 2 - Wall fixing brackets 6 - Decor panel fixing screws 4 - Security fixing screws Fitting the Wall Brackets 1. Use the paper template provided to mark the hole positions on the wall for the bracket fixing screws. 2. Check the hole distances are correct with a tape measure as stated on the template. 3. At this stage it is important to allow 15mm (1/2 ins) clear space above the cooker hood to enable it to be hooked onto the brackets and for subsequent removal for decorating or servicing. Hob A: Built-in Electric Hob: 650mm clearance B: Built-in Gas hob: 700mm clearance C: Slot-in Electric Cooker: 685mm clearance D: Slot-in Gas Cooker: 787mm clearance 12 Venting The hood is more effective when used in the extraction setting (ducted to the outside). Venting kits may be purchased through your retailer or DIY store, and must be ducted to an outside vent of 100mm (4 ins) minimum. The ducting used must be manufactured from fire retardant material. When the cooker hood is ducted externally the charcoal filter/s must be removed. To Fit the Ducting 1. Open the grille by pressing inwardly on the actuator bolts at each side of the grille, while pulling the grille panel downwards. The grille panel will slide into the intermediate position. Raise the lower edge of the grille forward through 45° angle until the grille becomes detached from the slide mechanism. 2. Align the flat sides on the spigot with the recesses in the top of the casing. Insert and snap fix the spigot into the casing. 3. Connect the 100mm (4 ins) ducting to the spigot and make an air tight seal. 4. Remove the charcoal filters. Recirculation The cooker hood is supplied specified for use in the recirculation mode with the charcoal filter/s fitted. In the recirculation mode contaminated air is passed through the charcoal filter/s to be purified and recirculated into the kitchen through the outlet on the top of the cooker hood. 13 Fitting the Cooker Hood to the Wall 1. Fit the brackets with the round ends facing downwards. 2. Once the brackets are secured, lift the hood squarely to the wall slightly higher than the brackets and lower the cooker hood until it is located onto the two brackets. Ensure that the cooker hood is correctly locat...