Оценок - 5, средний балл: 3.6
(
)
)
|
Фрагмент инструкции
All ducting must comply with local requirements and building codes. WARNING! Electrical Shock Hazard All electrical work must be done in accordance with local and/or national electrical codes as applicable. For safety, this product must be earthed. If you are unfamiliar with methods of installing electrical wiring, employ the services of a qualified electrician. Turn off power at service entrance before installing wiring or servicing this product. WARNING! (HC60) (HC90) Weight Hazard The wall canopy is heavy. Please ensure adequate care is taken when installing the wall canopy to prevent personal injury. The wall canopy must be installed onto a solid wall, stud, beam or truss. Weight of the product is 8.8 kg/10.7 kg. Installation instructions Contents of packaging 1 x wall canopy 2 x chimney flues with bracket 1 x installation instructions 2 x aluminium mesh filters (HC60PCHTX1) 3 x aluminium mesh filters (HC90PCHTX1) 2 x butterfly flaps 4 x small screws, to secure chimney flue 5 x 8 x 1.” wood screws 1 x washer (5 mm inner diameter) Typical equipment required: Electric drill Screwdriver Duct tape Jig saw Ladder Ducting Tape measure Drill bits Spirit level Accessories Fig.1 Wall canopy Accessory Part Number Chimney ext (740 mm) SS 790698 Light bulb 12V Halogen/Max 20W Charcoal filter (HC60) 790681 Replacement aluminium filter (HC60) 790682 Charcoal filter (HC90) 790683 Replacement aluminium filter (HC90) 790684 Installation instructions Height of wall canopy Where an electric cooktop is installed beneath the wall canopy, the distance between the top of the cooktop and the underside of the range hood must be a minimum of 600 mm and a maximum of 700 mm. Where a gas fuelled cooktop is installed beneath the wall canopy, the distance between the top of the pot rests and the underside of the rangehood must be a minimum of 650 mm and a maximum of 750 mm. Note: your relevant gas or local building authority may specify different height requirements. Care should be taken to comply with any applicable regulations concerning the discharge of exhaust air. Ducting options Note: if you wish to have the flue run all the way to the ceiling, please ensure that you work your measurements out fully before attempting the installation. In some instances, extra lengths of flue or a customised flue maybe required. A 740 mm flue extension is available as an accessory part for use where ceiling height is above 2440 mm. (Part no. 790698) Recirculation For recirculation, please purchase charcoal filters, which are fitted in place of the aluminium filters supplied with the hood. The charcoal filters purify the air before allowing the air to return back to the kitchen through the air vents in the sides of the chimney flue. Note: a ducting hole is not required in the wall or ceiling if the canopy is fitted with charcoal filters. Ducting For ducted installation, it is recommended that you use 150 mm diameter, rigid or semi-rigid ducting. To accommodate the 150 mm ducting, a ceiling hole should be carefully measured and cut out, 160 mm (min) in diameter, with a centre line 100 mm from the edge of the wall. Efficiencies in the performance of your canopy are enhanced by the use of smooth, straight and short ducting options. We recommend using solid, galvanised or plastic, smooth-walled ducting which helps to reduce noise and increase airflow. The use of flexible ducting is not recommended. If there is no other option available, the flexible ducting must be pulled as tight as possible. All ducting must comply with local requirements and building codes. Note: we recommend an Easy Fit by Fisher & Paykel or a UNIDUCT ducting system, products that have been designed to expel air efficiently. Installation instructions Preparing the wall canopy for installation Before installing the wall canopy, please carefully read through the installation instructions in full. Prior to drilling any holes, check that the area behind the surface to be drilled is clear of any electrical cables or pipes etc. Take care when installing the wall canopy as stainless steel is easily damaged during installation if scratched or knocked by tools. Protect the cooktop below, using cardboard or a similar protective cover, to prevent damage on installation. Installation instructions 1 Establish the desired height of the rangehood above the benchtop according to the ‘Installation height requirements’ above. Measure this distance from the top of the benchtop and, using a spirit level, draw a light horizontal line on the wall. Make sure that the line can easily be erased or will be hidden after installation. This is where the bottom of the rangehood will sit (Fig.2). 2 Mark the position of the rangehood on the wall. Using a spirit level, also mark a vertical line intersecting the horizontal line, (ensuring that the line can easily be erased or will be hidden after installation) showing the position where the centre of the rangehood will be. This is normally over the centre of the ...
Эта инструкция также подходит к моделям:Вентиляторы - WALL CANOPY HC90PCHTX1 (546.33 kb)