Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
3. Use only Kerosene or #1 fuel oil. Never use gasoline, naphtha, paint thinner, alcohol or other fuels of any kind. 4. For indoor use only. Use only in well ventilated areas. Provide at least 2 sq. ft. of opening near the floor and 2 sq. ft. of opening near the ceiling. (Also see "Operating Precautions"). 5. Install the heater such that is is not directly exposed to water spray, rain and/or dripping water. 6. Maintain minimum clearance from normal combustible material (like paper) at least 8 ft. from the heater outlet and 3 ft. from the top, sides and inlet. Locate 10 ft. from convas or plastic coverings and secure them to prevent flapping or movement. 7. Due to the high surface and exhaust temperatures, adults and children must observe clearances to avoid burns or clothing ignition. 8. Never use in areas normally for habitation and/or where children may be present. 9. Operate only on a stable, level surface. 10. Do not use with ductwork. Do not restrict inlet or exit. 11. Use only the electrical power specified. The electrical connection and grounding must comply with National Electrical Code - ANSI/NFPA 70 (USA) and CSA C22.1 Canadian Electrical Code, Part 1 (Canada). 12. Use only a properly grounded 3-prong receptacle or extension cord. 13. Do not move, handle or service while hot or burning. 14. Use only in accordance with local codes and federal ordinances. Mr. Heater |Kerosene Forced Air Heater 3 Operating Instructions and Owner’s Manual OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 1. Remove all protective material which may have been applied to the heater for shipment. 2. Remove heater from carton. 3. Check the heater for possible shipping damage. If any damage is found immediately notify the dealer from whom you purchased the heater. PREPARING FOR OPERATION 1. Check the heater for possible shipping damage. If any is found, immediately notify the factory. 2. Follow all of the "Precautions". 3. Fill the fuel tank with clean kerosene, No. 1 fuel oil or No. 1 diesel fuel only. Kerosene is recommended for use when the temperature drops below 0°F (-18°C). In extremely cold weather, condensation may develop in the tank and it is recommended that a tablespoon of de-icer be added for each gallon (4 liters) of fuel in the tank. When filling the heater, use at least 2 gallons (8 liters) of fuel. Be sure heater is level and do not overfill. Use a funnel or can with a long fill spout. IMPORTANT: Before filling fuel tank the first time or after extended storage periods, drain the fuel tank of any moisture or condensation. 4. Locate heater at a safe distance from combustible materials. Model MH50K is not suitable for use on wood floors or other combustible materials. When used, the heater should rest on suitable insulating material at least 1 inch think and extending 3 ft. or more beyond the heater in all directions. START 1. Plug heater into a well grounded 115V, 60HZ, 1O source of power. In cold weather, starting may be improved by holding a finger over the end of the pressure adjusting screw until the heater starts. This unit is equipped with a circuit breaker located near the power cord. If the unit does not start, check to see that the reset button is pressed in. STOP 1. Unplug the heater. RESTART AFTER SAFETY SHUTDOWN 1. Wait 5 minutes. 2. Push reset button. MAINTENANCE AND STORAGE WARNING: To prevent personal injury, unplug the heater from the wall outlet before servicing. For maximum effIciency and trouble-free service, make the following periodic maintenance, cleaning and inspections. DAILY SCHEDULE 1. GENERAL. Make general visual inspection of heater for loose or damaged parts. Check nuts and bolts to insure against looseness caused by vibration or rough handling. Damaged parts should be repaired or replaced before using heater again. Check heater operation to be sure it is operating normally (See "Servicing" section for description of normal operation). 2. FILTERS. Dirty air or fuel filters will cause an imbalance in the air-fuel mixture. The best indication that this condition exists is an increase in odors or difficulty getting your heater to ignite. This heater should never be operated without the filters in place. If required, clean filters as described under "500 Hours" and "Annual Schedules". 500 HOUR SCHEDULE 1. AIR INTAKE FILTER. Remove and wash the filter element with a mild detergent, dry thoroughly and replace. Do not oil the filter element. If your heater is used where there is considerable dust or dirt, clean as often as necessary (approximately every 50hrs.). 2. REMOVE DUST. Clean heater twice a season (more often under dusty conditions). Remove accumulated dust from the transformer, burner, motor and fan blades with compressed air. Wipe area clean with a clean dry cloth. Inspect area to insure all foreign materials are removed, especially around the burner and combustion area. 3. CAD CELL. Clean the glass portion of the cad cell with a soft dry cloth. 4. NOZZLE. Accumulation of dirt fro...