Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Please follow the bulb manufacturer’s instructions. ^ To change the halogen bulb first remove the lamp cover, a. ^ Pull the bulb, b, out of its socket and replace with a new one. ^ Return the lamp cover, a. Never use the lighting without the lamp cover, a, in place. The glass is specially made to filter harmful light rays. After Sales Service In the event of a fault which you cannot correct yourself please contact: – Your Miele Dealer or – The Miele Technical Service Department USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.ca When contacting the Technical Service Department, please quote the model and serial number of your appliance. These are shown on the data plate which is visible when the grease filters are removed. 18 Installation instructions Table of Contents Caring for the environment Installation accessories Plywood backing Electrical data Appliance dimensions Installation Retaining plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Attaching the canopy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Inserting the non-return flap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Exhaust connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Attaching the chimney extension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Attaching the chimney. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Air extraction Caring for the environment Disposal of packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances may contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Before discarding an old appliance, unplug it from the outlet and cut off its power cord and remove any doors to prevent hazards. See the Warning and Safety instructions. Installation accessories Installation accessories a 2 protective shields prevent scratches to the chimney during installation. b 2 hose clips for securing the ducting. c 1 reducing collar for use with 5" (125 mm) exhaust ducting. d 1 non-return flap e Upper retaining plate B secures the chimney extension. f Middle retaining plate C for additional stability of the chimney. g Lower retaining plate A secures the canopy and the motor assembly. 6 screws 5 x 60 mm 10 large headed screws 5 x 40 mm (S8 wall anchors included in the packaging are not for use in USA/CDN.) 2 M 6 locking nuts for securing the motor assembly. 4 screws 3.9 x 7.5 mm for securing the chimney and the chimney extension. CAUTION: During the installation process, please be careful of sharp edges that can cause harm. Plywood backing The majority of the weight of the installed ventilation system will be supported by retaining plate A. It must be firmly attached to the stud framing behind the drywall. If studs are not available in the required locations, a plywood backing (min. 1/2" (13 mm) thick) spanning at least two studs must be installed. Failure to adequately support the weight as stated may result in the ventilation system falling off the wall, causing personal injury and property damage. (If plywood backing is not needed, proceed to "Attaching the retaining plates to the wall." ) To install a plywood backing board ^Make a mark, S + 16 3/4" (425 mm) above the cooktop and on the center- line. ^Make a second mark 12 3/4 " (324 mm) underneath the first one. ^ Hold retaining plate A against the wall so that the marks are visible through the holes of the plate (see "Installation / Retaining plate A"). Draw a line around the plate’s perimeter, then set aside the plate. ^ Make a cutting line 3" (76 mm) above and 3" (76 mm) below the outline of plate "A". ^ Find the studs to the left and right of the mounting location by tapping the wall or using a stud finder. ^ Mark a vertical cutting line along the center of each stud. Be careful not to damage any wiring or plumbing that may be located behind the wall. Make sure that the power supply to the area where this installation is being performed has been turned off at the breaker panel before cutting into the wall. ^ Remove the drywall between the cutting lines and replace it with plywood of a matching thickness (min. 1/2" (13 mm) thick). Tape the joints and refinish the wall. ^ Proceed to "Attaching the Retaining plates to the wall" to complete the installation. Electrical data All electrical work sh...