Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Verify that the screws engage the wall framing. If not, wall anchors must be used. If additional support is required for the wall hood, drill supplementary mounting holes in the back plate and use these holes to attach the hood assembly to the wall framing. WIDTH OF HOOD WIDTH OF HOOD 261/4" (667) TO MOUNTING BRACKET HOLE CENTERS 131/8" (333) HOOD CENTERLINE USE ROUND AND SLOTTED HOLES TO SECURE HOOD TO WALL STUDS MOUNT BRACKETS TO WALL FRAMING 77/16" (189) TO TOP OF BRACKET Low-profilewallhoods—verticaldischarge. 261/4" (667) TO MOUNTING BRACKET HOLE CENTERS 221/2" (572) CENTERED ON HOOD 91/2" (229) CENTERED ON HOOD 131/8" (333) HOOD CENTERLINE USE ROUND AND SLOTTED HOLES TO SECURE HOOD TO WALL STUDS MOUNT BRACKETS TO WALL FRAMING 77/16" (189) TO TOP OF BRACKET WALL HOLE CUT-OUT Low-profilewallhoods—horizontaldischarge. Pro Wall Hood Installation 24" and 27" Deep Wall Hoods WALL PREPARATION Construct the wood wall framing flush with the wall studs and centered in the location that the hood will be mounted. Finish the wall surface. Attach the wood mounting support provided with the hood. Refer to the illustration below. The mounting support should be centered within the desired location of the hood. Use the 3" (76) screws provided to attach the mounting support to the wall. The screws should be located to correspond with wall framing and countersunk so that they are below flush. Install the retaining brackets to the wood mounting support at the locations shown in the illustration and the chart below. Use the #10 X 11/2" (38) screws and washers provided to secure the brackets in place. The brackets should be mounted 1/2" (13) above the top of the wood mounting support. WoodMountingSupport WIDTH OF HOOD A 30" (762) 113/4" (298) 36" (914) 121/4" (311) 42" (1067)* 151/4" (387) 48" (1219)* 181/4" (464) 54" (1372)* 211/4" (540) 60" (1524)* 241/4" (616) 66" (1676)* 271/4" (692) RETAINING BRACKET 1/2" (13) 151/8" (384) TO BOTTOM OF HOOD A 47/16" (113) 21/2" (64) MOUNTING HOLE For ease of installation, the location of the wood mounting support and retaining bracket allow for 1/2" (13) clearance at the top of the hood. This gap will be taken up during final mounting of the hood to the mounting support. Refer to the illustration below for the location of mounting holes for pro 24" (610) and 27" (686) deep wall hoods, one on each side of the back plate. Framing must be tied together and to ceiling joists to provide enough structural strength to support the weight of the hood and internal blower, if applicable. CENTER OF HOOD Wood mounting support. Location of mounting holes. Pro Wall Hood Installation wolfappliance.com/specs 24" and 27" Deep Wall Hoods HOOD PREPARATION IMPORTANT NOTE: For 24" (610) and 27" (686) deep wall hoods using an internal blower, refer to installation instructions provided with the blower assembly. Install the internal blower to the back plate assembly prior to mounting the hood. If a duct cover is to be used, follow the instructions on page 9 before installing the hood. If you are installing a recirculating kit, refer to instructions included with the kit before installing the hood. • The hood is shipped with the back plate and transition assembly attached. The transition is shipped upside down in the top of the hood. It must be removed and reinstalled in the proper position. • Remove the filters by pushing each filter up at the angle it is placed in, and rotate down. Remove the center filter first. Then take out the grease cups placed on the bottom edge of the hood coinciding with the bottom edge of the filters. Gloves should be worn when handling filters. • Detach the back plate and transition assembly from the hood by removing the top and back screws. Do not discard the screws, they will be used in the installation. Refer to the illustration below. • Separate the transition from the back plate by removing the shipping nut from the inside of the back plate. • Position the back plate in the desired location and mark the mounting holes on the wood support. Drill pilot holes for the mounting hardware. • If you are installing an in-line or remote blower, drill a 7/8" (22) hole through the wood framing for the conduit. Refer to the illustration below for location of the hoods' electrical box. Refer to the in-line and remote blower sections on pages 20–21 and follow installation instructions provided with the blower. IMPORTANT NOTE: Do not run electrical wiring for an in-line or remote blower through the ductwork. ELECTRICAL BOX Back plate and transition. Location of electrical box. Pro Wall Hood Installation 24" and 27" Deep Wall Hoods REATTACH BACK PLATE Attach the transition to the back plate using the four shipping screws provided in the hardware mounting kit. Reinstall the shipping screws removed previously from the top and back of the back plate. Seal with duct tape to ensure a tight seal from the transition to the back plate. If additional support is required, drill supplementary mounting ho...
Эта инструкция также подходит к моделям:Вентиляторы - 811504 (485.06 kb)
Вентиляторы - 811504 (485.06 kb)
Вентиляторы - Pro Wall (485.06 kb)