Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации Fagor America, модель SCFB-36X

Производитель: Fagor America
Размер: 1.13 mb
Название файла: 57d7332f-6b83-c194-f911-67a4a8b881de.pdf

Язык инструкции:enesfr

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста

Фрагмент инструкции


* In its sucking version (Fig.2), fumes are directly vented outside, through an evacuation duct connected with the superior part of the wall or the ceiling. Both coal filter and air deflector are not necessary in this case. * Before installing the appliance and in order not to damage the appliance itself, the metal grease filter should be removed. Such filter can be removed by pushing the special filter handle toward the back side of the range hood and turning it downwards so as to unfasten it from its slot (Fig.3B). Wall stirrup-fixing * Using the special drilling jig (Fig.4X), perforate the wall according to the pattern indicated by the jig itself, and pay attention in order not to damage water pipes and electric wires. Perforation should be performed with a O 8 mm walldrill. Then insert the proper plastic reinforcements (Fig.4A). The hood-bearing stirrup (Fig.4S) can be applied by using the screws provided with the equipment (Fig.4B). Now hook the range hood onto its bearing (Fig.5) and then adjust horizontally and vertically the position of the appliance by adjusting the special metric screws (Fig.6V,T). After the appliance is adjusted, fix it by inserting and tightening the safety screws properly (Fig.4C) WARNINGS USES INSTALLATION Fixing the ornamental chimney * Before fixing the chimney, place the electric feeding equipment into the ornamental pipe and provide a hole for the air outlet if the appliance is used in its sucking version. Warning! Before connecting the flexible exhausting pipe to the motor, make sure the stop valve, which is on the air outlet of the motor, can swing. Sucking version * Fix the pipe-bearing stirrup (Fig.7Y) to the wall or ceiling by using the proper reinforcements and screws in equipment. Connect the range hood flange with the evacuation hole by using a proper pipe. Perform the electrical connections. The superior end of the pipe is to be fixed laterally to the pipe bearing (Fig.8Y) by using the two self-threading screws. Now mount the inferior chimney by inserting it through the front side of the range hood and then turning it down until it is fixed inside (Fig.8). Filtering version * In the filtering version the air deviator is fixed through the screws supplied (Fig.9), by using the holes which are on the back of the upper telescopic section. Connect the flange of the appliance with the air deviator through an appropriate pipe. Connect the appliance with the electric mains. Mod. 5CFB-48X – 5CFB-36X – 5CFB-30X - Module - Luxury version (Fig. 10) A: Light switch on/off B: Motor switch on/off (1st rate level) C: 2nd rate level switch D: 3rd rate level switch E: 4th rate level switch F: 10-minute timer. * An accurate maintenance guarantees good functioning and long-lasting performance. * Particular care is due to the grease filter panel. It can be removed by pushing its special handle toward the back-side of the range hood and turning the filter downwards so as to unfasten it from its slot (Fig.3B). To insert the filter just perform the opposite operation. After 30 hours of operati...

Эта инструкция также подходит к моделям:
Вентиляторы - SCFB-30X (1.13 mb)
Вентиляторы - SCFB-48X (1.13 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории