Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
holes through the top holes in the bottom chimney and through the lower end of the top chimney duct. • Fasten the two chimneys to the centre chimney bracket. Top chimney duct Drill two 3.5mm Diameter holes and secure two chimney ducts to mounting bracket. Mounting bracket Bottom chimney duct Page 5 Grease filters. Grease filters. • Remove the plastic outer protective lining on the grease filters before fitting them to the extractor hood. • To fit the filters, engage the two lugs at the rear of each filter into the rectangular slots of the extractor hood frame, lift the filter and press the handle catch inwards . • Engage the filter and release the catch. • To remove the filter, for cleaning purposes, reverse the procedure described above. Optional Carbon pad filters. • Carbon pad filters assist in removing any unwanted cooking odours from the atmosphere. • If your installation ducts filtered air to the outside, the carbon pad filters are not required. • Should you require them, factory approved, carbon pad filters and installation kits may be purchased from your nearest Defy service Centre or their authorised agents. STEEL ROD REMOVED STEEL ROD IN PLACE GREASE FILTER CARBON PAD FILTER Page 6 Glass cover Retaining ring Light bulb Glass cover Retaining ring Light bulb Operation. • Select the fan speed you require. Motor speed • Push button ‘3’ for high extraction level. Off button • Push button ‘2’ for medium. • Push button ‘1’ for low. • The fan indicator light will glow when the fan is operating. 12 30 • To switch the fan off, push the motor speed OFF button ‘0’. Lights • If required, you may illuminate the Fan speed Fan on/ off indicator cooking area by switching the hood light lights on. • Leave the hood running for a short period after the cooking has been completed to clear any smoke and odours. Replacing the light bulbs. • Switch off the electricity supply. • If the bulb has recently failed, it might still be very hot. Allow the glass cover to cool before attempting to replace the bulb. • Hold the glass cover and unclip the retaining ring. Be careful not to let the glass cover fall. • Replace the light bulb with a commercially available OSRAM 12V 20W (64425) or equivalent bulb. • Fit the glass cover and replace the retaining ring. • Switch on the electricity supply. Housing Page 7 Maintenance and cleaning. Maintenance and cleaning. Important: Before cleaning any part of the hood, switch the power off at the mains. Cleaning the metal grease filters. • In normal operation (1 to 2 hours daily), the metal grease filters must be cleaned every 8 to 10 weeks. • The filters may washed in a dishwasher, however they may discolour slightly. • When hand cleaning the filters, soak them in hot, soapy water to loosen the grease. • Brush with a stiff nylon brush. • Rinse clean and allow to air dry before re-fitting. • If cleaning is not carried out in accordance with the instructions, the accumulated grease could, over time, become a fire risk. General cleaning. Stainless steel is not adversely affected by normal household use but because of its reputation for durability, it is sometimes assumed to be indestructible, and therefore subjected to misuse or even abuse. Care should be taken to avoid such ‘abnormal use’. Cleaning materials. Do use: • A moist lint free soft cloth or synthetic sponge. • Soap, or mild liquid detergent. • A mild window cleaner. • Diluted ammonia in warm water. • A nylon bristle brush. • Cleaners labelled “Suitable for stainless steel”. Do not use: • A steam cleaner. • Acid, alcohol, soda, chloride or spirit based cleaners. • Coarse abrasive cleaning powders. • Metallic scourers, steel wool, metal scrapers, or plastic scouring pads. • Wire brushes or emery paper. • So called “silver cleaners”. Cleaning procedure • Frequent cleaning is recommended rather than an occasional aggressive clean. • Routine cleaning will preserve the corrosion resistance and the appearance of the stainless steel for many years. • Clean the stainless steel as often as necessary (i.e. when it is noticeably dull or dirty) and use the simplest cleaning method that will effectively do the job. • Use clean water, or a mild detergent solution applied with a soft cloth or sponge. Rinse well and wipe dry. • Always wipe in the direction of the brushed texture on the stainless steel. • Periodically apply a fine film of dedicated stainless steel cleaner or baby oil to the canopy of the extractor hood to add lustre and sparkle to the steel. Page 8 Owner’s responsibility. Owner’s responsibility. NOTE: Since the following are not factory faults, they are the owner’s responsibility. • Damage to exterior finish. • Breakage of glass and other components. • Replacement of the light bulbs. • Damage through improper use or installation. Problem check. Before calling a service tec...
Эта инструкция также подходит к моделям:Вентиляторы - DCH260 (295.29 kb)
Вентиляторы - DCH261 (295.29 kb)
Вентиляторы - DCH285 (295.29 kb)