Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Connect white to white, black to black, and green to prepared hole with green ground screw provided. (FIG. 11) INSTALLING RANGE HOOD WARNING TURN OFF THE PROPER CIRCUIT AT THE SERVICE ENTRANCE BEFORE WIRING THIS RANGE HOOD. 6. Strip 1/2" of insulation foam wires. Connect white to white, black to black, and green to prepared hole with green ground screw provided. (FIG. 11) 1. Run electric wiring through hole drilled in wall or cabinet. Split wiring for 6" and install proper connector for type of wire used. (FIG. 9) FIG. 9 2. Position hood so that: a.) Wiring is routed through knockout opening. (FIG. 10) b.) Large part of keyhole slots fit over hood mounting screws. (FIG. 10) c.) Damper/duct connector slides into ductwork. (UXT3030AA, UXT3036AA, UXT4030AA, and UXT4036AA. FIG. 10 3. Adjust hood so that hood front is flush with cabinet frame. 4. Tighten hood mounting screws firmly. 5. Fasten wiring to hood with proper electrical connector for type of wiring being used. WARNING ALL ELECTRICAL CONNECTIONS MUST BE IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN. FIG. 11 7. Replace wiring box cover and screw. Make sure that all wiring is safely contained inside. 8. Install light (75 Watt maximum) For easier installation, squeeze plastic lens and remove it from hood. Remember to reinstall lens (FIG. 12) FIG. 12 9. Turn on power and check operation of fan and light. Make sure that damper operates freely. 5 USE AND CARE SWITCHES The fan and light are each controlled by a rocker switch. The light switch has two positions, "ON" AND "OFF". The fan switch has three positions - "HIGH", "LOW" and "OFF". ("OFF" is the middle position.) FILTERS UXT3030AA, UXT3036AA, UXT2030AA, and UXT2036AA Hoods Only: Remove aluminum filter by turning filter retainer to one side. (FIG. 13) Filter should be washed once a month in a hot detergent solution. Aluminum filters are dishwasher safe. when installing filter, make sure that filter slides under retaining tabs on back of fan housing. Turn filter retainer so that arrows on retainer point toward front and back of hood. FIG. 13 UXT4030AA and UXT4036AA Hoods Only: The UXT4030AA and UXT4036AA hoods are equipped with a ductfree filter. Remove filter by turning filter retainer to one side. (FIG. 13). The ductfree filter is not washable, and will last up to twelve months with normal use. Replace the filter when colored side becomes noticeably dirty or discolored. When installing filter, make sure that filter slides under retaining tabs on back of fan housing. MAKE SURE THAT COLORED SIDE OF FILTER IS NEXT TO FAN WHEN FILTER IS INSTALLED. Turn filter retainer so that arrows on retainer point toward front and back of hood. WARNING ALWAYS DISCONNECT ELECTRIC POWER BEFORE SERVICING RANGE HOOD. FAN ASSEMBLY Remove filter. Remove two screws holding motor bracket to range hood, and unplug fan assembly. Be careful not to allow fan assembly to drop when screws are removed. (FIG. 15) FIG. 15 CLEANING Clean your hood with a mild detergent suitable for painted surfaces. DO NOT USE ABRASIVE CLOTH, STEEL WOOL PADS OR SCOURING POWDERS. Fan assembly may be vacuumed. Fan assembly is lifetime lubricated, and never needs oiling. HOW TO AVOID A COMMON RANGE-TOP GREASE FIRE • Your range hood provides a protective barrier between the cooking surface and th...
Эта инструкция также подходит к моделям:Вентиляторы - UXT2030AA (543.97 kb)
Вентиляторы - UXT2036AA (543.97 kb)
Вентиляторы - UXT3036AA (543.97 kb)
Вентиляторы - UXT4030AA (543.97 kb)