Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
For vertical discharge, remove the knockout in the top of the hood. 3. Install Internal Blower (DAH95 models only) If your hood is already equipped with a blower, or you will be using a remote blower, proceed to Step 4: Install Transition (next page). 1. Remove rear filter rail. 2. Remove blower control wire cover. 3. Remove J box. 4. With hood standing on its back wall, place blower in center of hood. 5. Screw 6 screws (3 on each side) through mounting plates. See Figure 2. Figure 2 - DAH95 models with internal blower Connector Access Panel Blower Cord Connector J Box Rear Filter Rail Figure 3 - DAH95 models with remote blower Rear Filter Rail J Box Connector Access Panel Blower Cord Connector Blower Mounting Plate Remote Wire Cover White Connector J Box Rear Filter Rail 3 Installation 4. Install Transition For internal blower installation, install the 7” transition (included) to connect to 7” ducting. If 7” ducting is not available, 8” ducting may be used. In this instance, an additional 7-8” transition must also be used (not included). For remote blower applications, 10” ducting is required. In this instance, a 7”-10” transition must also be used. Attach the transition with 4 #8 sheetmetal screws (included) and seal connection with duct tape. 5. Mount the Hood The DAH model hood can be mounted through the back wall or through the top. See General Information, page 1, for suggestions for hood height. Once the preferred height is determined, locate the centerline (left to right) of the cooking appliance. Wall Mount 1. From the centerpoint of the cooking appliance, measure up to the preferred height. Measure up an additional 9” to locate the centerline of the screw holes (see Figure 4). 2. Install toggle bolts through drywall leaving 1/4” of the bolt exposed. Install one togglebolt 11 1/2” to the left of the centerline and one togglebolt 11 1/2” to the right of the centerline. These are the only installation points for the 30” hood. See Figure 4 For the 36” hood, there are 2 additional installation points. These are also at the centerline height, but are 15 3/8” from the centerline in each direction. See Figure 4. 3. Place the hood by sliding the mounting holes in the hood over the bolts. 4. Tighten the bolts. Top Mount 1. Install the hood flush against the back wall. 2. Identify the centerline on the mounting surface (underside of cabinet). 3. Place the hood and install the drywall screws through the mounting holes. Insert 3 drywall screws 11 1/2” off the centerline in both directions at the following depths: 1. 2 1/4” from the back wall 2. 8 1/4” from the back wall 3. 9 1/4” from the back wall (See Figure 5). The 36” hood also requires 3 additional screws, at the same depths, on each side (total of 6). These are 15 3/4” from the center line (See Figure 5). 4. Place the hood. 5. Tighten the screws. Figure 4 - Wall Mount CL 30" - 36" 11-1/2" from CL 15-3/8" from CL 9" Figure 5 - Top Mount CL 1" 6" 2 1/4" Back Front 4 Installation 6. Connect Wiring Accessories WARNING: Use only spring type wire nuts (included) to make electrical connections. Replacement wire nuts must be rated for a minimum of (2) #18ga wires and a maximum of 4 #14ga wires, UL & CSA rated to 600V and 302. F/ 150. C. Request #189692 when ordering from BSH. The following accessories are available from your Bosch dealer or through Bosch Service: 800-944-2904. Please reference the model number when requesting these items. For Internal Blower Use: See Figure 1 or 2, page 3. 1. Remove electrical knockout behind J box and install 1/2” conduit connectors. 2. Run 120V AC 60Hz, 15A supply wires through 1/2” conduit to hood electrical knockout behind J box cover. 3. Connect blower cord wires to house wiring through electrical knockouts. Use wire nuts supplied (white to white, black to black, green to green). 4. Connect blower cord at white connector behind connector access panel (if not already connected). Verify that connectors are tightly connected. For Remote Blower Use: See Figure 3, page 3. 1. Remove 2 hood electrical knockouts and install 1/2” conduit connectors. 2. Run black, white and green supply wires through *for use with DAH95 models only 1/2” conduit to hood electrical knockout behind J box. Accessory Model # 6” Duct Covers 30” 36” Biscuit DCZ7607UC N/A Black DCZ7606UC DCZ9666UC Stainless Steel DCZ7605UC DCZ9665UC White DCZ7602UC DCZ9662UC 12” Duct Covers 30” 36” Biscuit DCZ7207UC N/A Black DCZ7206UC DCZ9266UC Stainless Steel DCZ7205UC DCZ9265UC White DCZ7202UC DCZ9262UC Recirculation Kit 30” 36” Biscuit DRZ7007UC N/A Black DRZ7006UC DRZ9066UC Stainless Steel DRZ7005UC DRZ9065UC White DRZ7002UC DRZ9062UC Charcoal Filter DHZ7960UC 3 1/4 x 10Transition DHZ3410UC Blowers* Integral Blower, 400 CFM DHG4001UC Integral Blower, 600 CFM DHG6001UC Remote Blower, 600 CFM DHG6003UC Remote Blower, 1000 CFM DHG1003UC Figure 6 - Remote Blower Pigtail Assembly 3. Connect power supply wires to hood wires behind J box (white to white, black to black, green ...
Эта инструкция также подходит к моделям:Вентиляторы - DAH93 (131.73 kb)