Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
6. Avoid contact with moving parts. 7. Do not operate in the presence of explosive and/or flammable fumes. 8. To avoid fire hazard, NEVER place the cord under rugs or any parts near an open flame, cooking or other heating appliance. 9. Do not operate any appliance with a damaged cord or plug after the appliance malfunctions, or has been dropped/damaged in any manner. Discard fan or return to an authorized service facility for examination and/or repair. 10. The use of attachments not recommended or sold by the appliance manufacturer may cause hazards. 11. Do not use outdoors. 12. Do not let the cord hang over the edge of a table, counter or come in contact with hot surfaces or leave exposed to high traffic areas. 13. To disconnect, grip plug and pull from wall outlet. Never yank on cord. 14. Always use on a dry, level surface. 15. Do not operate fan until fully assembled with all parts properly in place. 16. This product is intended for household use ONLY and not for commercial or industrial applications. 17. WARNING: To reduce the risk of electrical shock injury to persons, do not use in window. 18. WARNING: This fan is provided with an internal electronic fan speed control. To reduce the risk of fire or electric shock, do not use this fan with any other solid-state speed control device. INSTALLATION INSTRUCTION PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS ASSEMBLY INSTRUCTIONS Assembly Time: 5-10 Minutes NOTE: Check all packaging materials and make sure that you have all of the parts necessary for assembling your fan. 1. Insert the threaded end of the Lower Pole into the Base. Refer to Figure 2. 2. Secure the Base Weight to the threaded end of the Lower Pole with the Base Weight Nut. Refer to Figure 2. 3. Insert the threaded end of the Upper Pole into the Lower Pole. Twist clockwise to lock. Refer to Figure 3. 4. Slide Neck of the Motor Housing over the Upper Pole and secure by tightening the Thumb Screw. 5. Secure the Rear Grill to the Motor Housing by tightening the Rear Grill Mounting Nut. Refer to Figure 4 for the correct positioning of the Rear Grill to the Motor Housing. 6. Secure the Fan Blade to the Motor Shaft by tightening the Fan Blade Cap. Refer to Figure 5. 7. Secure the Front Grill to the Rear Grill by snapping the Front Grill into the clips around the perimeter of the Rear Grill. OPERATING INSTRUCTIONS 1. Set fan on a dry, level surface. 2. Plug cord into any standard 120 volt AC outlet. 3. The speed/mode is adjustable by pushing the Mode/ Off ( ) button either from the fan housing or the remote control. OSCILLATION INSTRUCTIONS: To turn the oscillation feature off pull the Oscillation Control Knob ( ) all the way up. To turn the oscillation feature on push the Oscillation Control Knob ( ) all the way down. FCC STATEMENT Potential for Radio/Television interference This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If the product does cause harmful interference to radio or television reception, which can be determined by turning the product on or off, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the product and the receiver. • Connect the product into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. REMOTE CONTROL This unit includes two (2) AAA batteries. Battery Replacement a) Locate the battery cover on the back of the remote control handset. Slide the battery cover off with your thumb. b) Use the tip of a pen to loosen each battery. Hold the remote control handset at an angle to allow the batteries to slide out. c) Insert two new batteries, pressing them firmly into their slot. d) Replace the battery cover. NOTES: • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. • Replace all batteries of a set at the same time. • Clean the battery contacts and the devices’ contacts prior to installing the batteries. • Remove the batteries from the equipment when it is not being used for an extended period of time. • Remove the used batteries promptly. THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the other). To reduce the risk of electric shock, th...
Эта инструкция также подходит к моделям:Вентиляторы - BSF152T (535.39 kb)