Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
. . . . . )%. . . . . . . . . . %%). . . !. +. %, . -&.&/.%%. . % . ). 0'.//1.%%. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Merloni Elettrodomestici UK Ltd., Morley Way , Peterborough, PE2 9JB 2 O 150mm O 150mm D min. 135 87 1 2 3 4 B E E P M Q L E D 5 6 7 F G H C Fig. 9 Fig. 12 8 6 5 3 Fig. 8 Fig. 10 Fig. 11 4 1 4 2 7 8 9 11 10 12 G. INSTRUCTION ON MOUNTING AND US. Consult the designs in the front pages referenced in the text b. alphabet letters. Closely follow the instructions set out i. this manual. All responsibility, for any eventual inconveniences. damages or fires caused by not complying with the instruction. in this manual, is declined. Installation The cooker hood must be placed at a minimum distance o. 50 cm from the cooking plane for electric cookers and 65c. for gas or mixed cookers. The hood is equipped with a top air outlet B (Fig. 2) fo. discharge of fumes to the outside (Ducting version . exhaust pipe and pipe fixing clamps not provided). Should it not be possible to discharge cooking fumes and vapour t. the outside, the hood can be used in the filter version, fitting a. activated carbon filter (in the case of the model with two suctio. motors then two active carbon filters are required), a discharge tube. for the expulsion of fumes, should be mounted on the connection rin. C (Fig. 7) situated on the top of the wall cabinet (discharge tube an. fixing brackets are not supplied). The models with no suction motor only operate in ducting mode, an. must be connected to an external suction device (not supplied). Preliminary information for installation of the hood. Disconnect the hood during electrical connection, by turning th. home mains switch off. 1. Fix the 2 brackets D (Fig. 1) to the side panel of the wall cabine. (one per side) with 2 screws for each bracket (align the bracke. to lower border). Position the bracket to touch the back border of the wal. cabinet, considering that the back border of the bracke. corresponds to the back side of the cooker hood. If the cooker hood is provided with a spacer, in case o. use, move the bracket forward to the same thicknes. as the spacer. Drill a hole on the ceiling of the wall cabinet to pass th. discharge tube and the electrical cable (the quot. indicated in Fig. 1 does not include the eventual spacer). 2. Fix 2 brackets E (Fig. 2) to the sides of the cooker hoo. (one per side). a. remove the extractable part of the cooker hood. b. Remove the grease filter(s) and, if envisaged, th. carbon filter(s). ttention, to be carried out only the first time the carbo. filter is removed. To avoid damage during transport, the handle of th. carbon filter is blocked with a screw. Remove the screw before dismantling every carbo. filter; the screw is not to be reused. c. fix the brackets with two screws P per bracket fro. inside the cooker hood, affix them as more as possibl. upwards (air exit side) and then serrate the screws. 3. Fix the aesthetic mask Q from the inside of the cooke. hood using two screws, (if supplied - Fig. 3 . the L tab. present on the body of the cooker hood serve as furthe. fixing for the mask and should be visible once the mas. has been fitted) and then finally affix the spacer M wit. three Clips from the external part of the cooker hood (i. supplied - Fig. 4). 4. Insert the cooker hood in the wall cabinet, ensuring t. position the cooker hood bracket E above the wal. cabinet bracket D (Fig. 5). Thread the electric cable through the appropriate perforation. 5. Block the cooker hood with two screws on the frontal par. (Fig. 5 . one per side). 6. Connect the cable to the electrical mains, only when th. installation is completed. 7. If the cooker hood should not touch perfectly with th. lower border of the wall cabinet then regulate b. loosening the screws P of the brackets E mounted o. the cooker hood (Fig. 2), it will be possible to regulat. the perfect matching of the cooker hood and wall cabinet. once regulated tighten the screws. 8. Regulate the gliding of the extractable drawer in relatio. to the depth of the wall cabinet by acting on the two skirtin. boards. F. (Fig. 6). In this way it will be possible to place the front in line wit. the wall cabinet (Fig. 6). a. Loosen the screws on the skirting board F. b. Move the ledges backwards or forwards depending o. requirement. c. Lock in the screws on the ledges. 9. Install a discharge tube on the connection ring C supplied. preferably with a diameter equivalent to the connectio. ring (Fig. 7). the discharge tube should be sufficientl. long to reach outside (Suction version) or the ceiling o. the wall cabinet (Filter version). 10. Fix the connection ring C (snap into place), at the uppe. exit of the cooker hood. To ease the installation, the ring is equipped with an index G tha. should correspond to the appropriate guide H placed on th. upper air exit. 11. Complete the installation of the ...