Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
It should be removable for service or maintenance. •Do not use silicone sealant to secure the hood to the wall. •You must be able to isolate the extractor from the mains electrical supply after installation. •This extractor has been designed to be used in a room with a volume of less than 36 m3 . •Steam cleaners must not be used when cleaning this appliance. •The performance of your extractor will vary depending on a number of factors. These include: type of extraction, length of ducting, room volume, ventilation available and cleanliness of the filters. 1 Using your Extractor Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for approximately 15 minutes after the end of cooking. A - Light switch B - Power indicator light C - Power switch To switch the extractor light on or off • Slide the light switch to position A1 for off, or A2 for on. To switch on the extractor, or change the motor speed • Slide the power switch to the position required dependent on the speed you require. To switch the extractor off • Slide the power switch to position C1 for off. Fig. 1 C2 C4 A B C A1 C1A2 C3 2 Care and Maintenance Care and Maintenance IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. Cleaning You should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. You can clean you extractor effectively by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth, for example the CDA E-Cloth. Cleaning the grease filter The grease filters should be kept clean to minimise the risk of fire. At least once a month you should remove and clean the grease filters with hot soapy water. You can also wash the grease filters in a dishwasher, ensuring that you place it in an upright position to prevent damage from other items in the dishwasher. After rinsing and drying, replace the filters. To remove the grease filters, pull open the handle on the grease filter.. It will release at the handle side. Then lower the grease filter to remove it completely. To replace the grease filter, repeat the steps in reverse. Please note: Cleaning the grease filters in the dishwasher may lead to discolouration. This is normal and does not constitute a fault with the appliance. Changing the charcoal filter (re-circulating only) To ensure best performance of your extractor, you should replace the charcoal filters every four to six months, depending on use. To attach a new charcoal filter, first remove the grease filters as described above. Then offer up the charcoal filter to the side of the motor as shown in figure 2 and turn it clockwise until it locks into place. Repeat with the other charcoal filter on the other side of the motor. Then replace the grease filters and cover panels. Fig. 2 3 Changing the Light IMPORTANT: DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWITCHING OFF THE ELECTRICITY SUPPLY. DO NOT CHANGE THE LIGHT BULB IMMEDIATELY AFTER USE AS THE BULB WILL BE HOT. ALLOW IT TO COOL BEFORE REMOVING IT. 1. Remove the grease filters as described above. 2. Remove the faulty light bulb and replace with a light bulb no more powerful than that specified on the rating plate. 3. Replace the grease filters. Do not touch bulbs or adjacent areas during or straight after prolonged use of the lights. The light is designed for use during cooking and not for general room illumination. Extended use of the light can reduce the lifespan of the bulb. Bulb replacement is not covered by the guarantee. Only use bulbs recommended for your extractor. Do not fit bulbs of a higher power rating. Bulbs of a lower power rating may be adequate for use, generally last longer, and use less energy. Spare bulbs are available from CDA Customer Care or from your local DIY shop. Mains Electricity Connection DOUBLE POLE SWITCHED FUSED SPUR OUTLET USE A 3 AMP FUSE Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSED SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. The wires in the mains lead of this appliance are coloured in accordance with the following code: BLUE = NEUTRAL, BROWN = LIVE. As the colours of the wires in the mains lead for the appliance may not correspond with the coloured markings identifying the terminals connecting to the fused spur, proceed as follows: •The wire which is coloured blue must be connected to the terminal marked N (Neutral), or coloured black. •The wire which is coloured brown must be connected to the terminal marked L (Live), or coloured red. NOTE: USE A 3A FUSE Assembly and electrical connection s...