Оценок - 5, средний балл: 4.2
(
)
)
|
Фрагмент инструкции
Rotate the blower wheel by hand to ensure it spins freely. Now plug the fan motor into the receptacle (Figure 10). SECTION 4 Ducting CAUTION: ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL BUILDING CODES. 1. Connect the ducting to the fan’s duct collar (Figure 8). Secure in place using tape or screw clamp. Always duct the fan to the outside through a wall or roof cap. NOTE: If damper detaches from unit, reattach by snapping the collar back onto the unit. It is designed to only fit one way. SECTION 5 Figure 8 Figure 7 Figure 9 Hot (Black) from house Neutral (White)Hot (Red) Hot (Yellow) Figure 10 Wiring CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE STARTING INSTALLATION. CAUTION: ALL ELECTRICAL CONNECTIONS MUST BE MADE IN ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN. 1. Run wiring from an approved wall switch carrying the appropriate rating. One neutral (white), one ground (green or bare copper), and three hot (black, red, yellow leads connected to the switch, one for each function). Secure the electrical wires to the housing with an approved electrical connector. Make sure you leave enough wiring in the box to make the connection to the fan’s receptacle. 2. From where you have access to the fan’s junction box, connect the white wire from the house to the two white wires from the fan. Connect one hot (black) wire from the wall switch to the black wire from the fan (this is the fan control). Connect second hot (red) wire from the wall switch to the red wire from the fan (this is the main light control). Connect the third hot (yellow) wire from the wall switch to the yellow wire from the fan (this is the night light control). Connect the ground wire from the house to the green wire from the fan (Figure 9). Use approved methods for all connections. 2. Plug cord from lamp holders into the appropriate receptacle (Figure 11). GroundSupply 211572097 Rev. A 8-05 3 of 12 3. Reinstall the light reflector by securing in place on the mounting bolt with the flat washer then the reflector, two lock washers and reflector nut. Tighten nut fully (Figure 12). Figure 11 Figure 12 Flat Washer Reflector Lock Washers Nut Figure 11 Figure 12 Flat Washer Reflector Lock Washers Nut CAUTION: FAILURE TO SECURE THE REFLECTOR BOLT MAY RESULT IN A RATTLING OR HUMMING NOISE. 4. Install the appropriate bulbs (not included) specific to your model: AK863L: Install a 100 watt maximum, type A19 medium base incandescent bulb (not included) and a 7 watt maximum type C7 (candelabra base) night light (not included). AK863FL: Install a 26 watt maximum, 2 pin quad, G24-d3 5. SECTION 7 Use and Care CAUTION: MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL BEFORE SERVICING THE UNIT. 1. Cleaning the Grill: Remove grill and use a mild detergent, such as dishwashing liquid, and dry with a soft cloth. NEVER USE ANY ABRASIVE PADS OR SCOURING POWDERS. Completely dry grill before reinstalling. Refer to instructions in Section 6 Completing the Installation, to reinstall grill. 2. Cleaning the Fan Assembly: Wipe all parts with a dry cloth or gently vacuum the fan. NEVER IMMERSE ELECTRICAL PARTS IN WATER. CAUTION: ALLOW BULB TO COOL BEFORE REPLACING 3. Changing the Light Bulb: Disconnect power to the unit. Remove grill by pulling downward on grill and squeezing grill springs together to release from housing (Figure 14). Incandescent Bulb (AK863L): Unscrew bulb from lamp holder and replace with a 100 watt maximum, type A19 medium base incandescent bulb. Fluorescent Lamp (AK863FL): Remove lamp by gently rocking lamp back and forth while applying outward pressure to release the lamp from the base. Replace with a 26 watt maximum, 2 pin quad, G24-d3 fluorescent lamp. Night Light (AK863L, AK863FL): Unscrew night light bulb from socket and replace with a 7 watt maximum type C7 (candelabra base) night light bulb. Sylvania model: CF26DD/841 GE model: F26DBXT4/SPX41 Phillips model: PL-C 26W/41/ALTO Refer to instructions in Section 6 Finishing the Installation, to reinstall grill. fluorescent lamp (not included) and a 7 watt maximum type C7 (candelabra base) night light (not included). Sylvania model: CF26DD/841 GE model: F26DBXT4/SPX41 Phillips model: PL-C 26W/41/ALTO Install the grill by squeezing the two ends of the springs together and installing them up into the slots on the fan’s housing. Push the grill up into position (Figure 13). CAUTION: WHEN INSTALLING GRILL, BE CAREFUL NOT TO PINCH FINGERS BETWEEN GRILL AND CEILING. Figure 14 Figure 13 6. Restore power and test your installation. 211572097 Rev. A 8-05 4 of 12 Troubleshooting Guide Trouble Probable Cause Suggested Remedy 1. Fan does not operate when the switch is on. 1a. A fuse may be blown or a circuit tripped. 1b. Connector plug from motor is not plugged in. 1c. Wiring is not connected properly. 1d. Motor h...