Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED CONTROL DEVICE. 7. DO NOT use fan in a window. Rain may create an electrical hazard. 8. Completely reassemble fan, according to instructions before reconnecting to power supply. Rev. E 4/01 1 Commercial Style fan WARNING: This fan should be used only in a clean, dry environment. Mounting of this product in any way other than specified in the instruction sheet will null and void the manufacturers warranty. WARNING: BECAUSE OF SIZE AND WEIGHT OF THIS FAN, MAKE SURE ALL PARTS ARE COMPLETELY ASSEMBLED ACCORDING TO INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN FAN COMING APART DURING OPERATION AND/OR PERSONAL INJURY. WALL/CEILING BRACKET INSTALLATION NOTE: ALWAYS INSTALL THE BRACKET TO A MINIMUM OF 2 X 4STUDDING. 1. Lay Fan Head on flat surface, so the front side is facing down. 2. 3. 4. Loosely attach one Grill Knob and one Rubber Spacer to the Head Assembly. Attach the other Grill Knob and Rubber Spacer to the Head Assembly and FIRMLY tighten. Return to the first Grill Knob and FIRMLY tighten. (Figure 1) Grill Knob Rubber Spacer Rubber Spacer Grill Knob Figure 1 Yoke Locate the wall or ceiling stud nearest to the desired Fan location. Following the proper mounting diagram, attach the Bracket to the stud using three (3) 5/16" diameter x 2" long Lag Screws (Not Supplied) or appropriately sized Bolts and Nuts if attaching to "I" beams. Wall Mount Assembly (Figure 2) Ceiling Mount Assembly (Figure 3) Insert Bolt through Yoke, Bracket, Pivot Hole, Flatwasher, and into Locknut. (Figure 2) or (Figure 3) While holding Fan in the desired position, firmly tighten the 7/16" Bolt. Figure 2 (Wall Mount Assembly) Fan Head Nut Wall Stud Figure 3 (Ceiling Mount Assembly) Fan Head Bolt Yoke Bracket Yoke Bracket Flatwasher Pivot Hole Pivot Hole Flatwasher Ceiling Stud Nut Bolt MODEL 4TM61C/9020C MANUAL DE INSTRUCCIONES DE OPERACION Y PARTES MODEL 4TM61C/9020C MANUAL DE INSTRUCCIONES DE OPERACION Y PARTES CAUTION: THE SECONDARY SUPPORT CABLE PROVIDED SHOULD BE USED FOR ADDITIONAL SAFETY. SECONDARY SUPPORT CABLE 1. Loop one end of cable around the Yoke. (Figure 5) 2. Attach a Cable Clamp with the "U" on the tail side of the loop leaving a tail approximately 1 to 2 inches. Tighten clamp nuts to 32 inch- pounds torque forming a tight loop. Make sure no part of the cable interferes with the blade. (Figure 5) 3. Wrap the other end of the cable around a secure building joist, truss, or other support near the Fan. If none of these are available wrap cable around the bracket. (Figure 4) Take up excess slack in the cable. Secondary Support Cable Yoke Tight Loop In Cable 1" - 2" Tail Figure 4 Figure 5 20 21 22 25 8 14 12 1110 13 7 11 10 18 17 16 15 19 23 25 24 24 8 26 26 5 6 2 43 1 9 Rev. E 4/01 2 CAUTION: USE ONLY THE MOUNTING HARDWARE WHICH IS RECOMMENDED FOR USE ON THIS FAN. 4. Attach the remaining Cable Clamp as indicated in step 2. The excess tail should be trimmed to extend 1 to 2 inches past the Clamp. 5. Check the assembly to assure the Blade is free of all obstructions. 6. Plug the power cord into a properly grounded three-prong receptacle. CAUTION: USE OF THE SECONDARY SUPPORT CABLE DOES NOT GUARANTEE PROTECTION AGAINST INJURY OF PERSONS, MOUNTING OF BOTH THE CIRCULATOR AND CABLE COULD FAIL IF SUBJECTED TO ABUSE, NEGLECT OR IMPROPER INSTALLATION. OPERATION 1.Plug in cord and select desired operating speed with pull cord. 2. WARNING: This fan should be used only in a clean, dry environment. Mounting of this product in any way other then specified in the instruction sheet will null and void the manufacturers warranty. MAINTENANCE WARNING: ALWAYS UNPLUG THE CORD BEFORE SERVICING. CLEANING: Use a soft cloth and a mild soap solution such as liquid dish washing detergent. CAUTION: Do not use gasoline, benzine, thinner, harsh cleaners, etc. which will damage the fan. Dry all parts with a soft cloth complet...
Эта инструкция также подходит к моделям:Вентиляторы - 4TM61C (133.02 kb)