Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
If ducting does not fit securely, an adapter may need to be purchased. Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. 42950-01 04/18/2007 6 A19J A20 0000IA18 0000A17 ONOFFA21 A22E1Go to stepon page 17 to attach grille. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. Turn on the power source. Secure the motor by tightening the 2 screws. Test the motor. If the motor does not run, check the plug connection. 42950-01 04/18/2007 7 5/81/25/81/2B12 B11EF FB13 1/8” bitB14 New Construction – suspended between joists B15 Slide the mounting rails into brackets. Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. Mark position of screws by using holes as a template. Drill a hole in the center of each outline. B16 Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. 42950-01 04/18/2007 8 B17 A3 Pin2 PinFan MotorLightLightGreenBlackBlackWhiteBlackBlackWhiteWhiteBare CopperGroundB19 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light Together *Option B18 GHB20 B21 Tighten screws. Route wires through the strain relief. Connect wires as shown. Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. 42950-01 04/18/2007 9 B22I IB23 B24J B25 B27E1Go to stepon page 17 to attach grille. ONOFFB26 Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. Secure the motor by tightening the 2 screws. Turn on the power source. Test the motor. If the motor does not run, check the plug connection. 42950-01 04/18/2007 10 EXISTING FANC11 NO EXISTING FAN 8”8 1/2” C12EF Existing Construction – accessible from above OR C14 5/81/25/81/2C13 Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8 1/2”). Use the motor housing as a template to mark position. Cut out an opening for the housing. Slide the mounting rails into brackets. Mark position of screws by using holes as a template. Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. 42950-01 04/18/2007 11 C16 C15 C18 C19 Insert screws, leaving space between the screw head and the joist. Screws are not provided. Drill a hole in the center of each outline. C17 Attach the rails onto the screws. Tighten screws. C20 Connect 4” duct and vent to the outside. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Route wires through the strain relief. 42950-01 04/18/2007 12 A3 Pin2 PinFan MotorLightLightGreenBlackBlackWhiteBlackBlackWhiteWhiteBare CopperGroundC22 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light Together *Option C21 HGC23 C24I Tighten the strain relief screws. Connect wires as shown. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. 42950-01 04/18/2007 13 C26J C25I C27 ONOFFC28 C29E1Go to stepon page 17 to attach grille. Secure the motor by tightening the 2 screws. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. Test the motor. If the motor does not run, check the plug connection. Turn on the power source. 42950-01 04/18/2007 14 EXISTING FAND11 21D14 Existing Construction – accessible only from below FD12 FD15 Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8 1/2”). Move the housing into position above the ceiling D13 Route wires through strain relief. Attach existing ducting to duct connector. Tape joints. If ducting does not fit securely, an adapter may need to be purchased. Install the housing flush with the sheetrock and secure by tightening the pre-loaded screws into the joist. 42950-01 04/18/2007 15 A3 Pin2 PinFan MotorLightLightGreenBlackBlackWhiteBlackBlackWhiteWhiteBare CopperGroundD16 Main Switch 1 (AC In) Switch 2 (AC In) *Option Fan & Main Light Together *Option GD17H Connect wires as shown. ID18 Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. D20J ID19 Secure the motor by tightening the 2 screws. Reinstall the motor by inserting the tabs and p...