Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 5. Connect the electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green as shown on Figure 14. -Store wires in the wiring box. Figure 14 10 Duct Cover Installation 6. Mark the position of the inner duct cover- mounting bracket {J} (provided). Use reference E from TABLE 2 and Measurements and Diagrams on page 20-21. Attach and secure inner duct cover-mounting bracket {J} with two screws (not provided) to the wall. Refer to Figure 15. NOTE: Inner duct cover will be attached to the mounting bracket. 7. Use 7” round steel pipe (follow building codes in your area) to connect the round exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. 8. Slide the inner duct cover up 2 inches before sliding the entire duct cover onto the hood. Refer to Figure 16. 9. Adjust the height of the inner duct cover to the inner duct cover-mounting bracket {J}. Secure the inner duct cover with two (1/8” x 3/8”) screws (provided). 10. Fasten outer duct cover to outer duct cover- mounting bracket {K} with two (1/8” x 3/8”) screws (provided) as shown in Figure 17. Accessories 11. Drop oil tunnel into recess support near rear of hood. Refer to Figure 18. 12. Install baffle filters and stainless spacer(s). Refer to Measurements and Diagrams on page 22 for baffle filter and stainless spacer placement. Angle baffle filter toward back of hood . Push baffle filter up until almost level . Slide forward into recess behind the front of hood . Lower baffle filter . Slide back until it fits into resting position . Refer to Figure 19. 13. Repeat step 12 to install all baffle filters and stainless spacer(s). Figure 15 Figure 16 Figure 17 Figure 18 Duct Cover Installation 6. Mark the position of the inner duct cover- mounting bracket {J} (provided). Use reference E from TABLE 2 and Measurements and Diagrams on page 20-21. Attach and secure inner duct cover-mounting bracket {J} with two screws (not provided) to the wall. Refer to Figure 15. NOTE: Inner duct cover will be attached to the mounting bracket. 7. Use 7” round steel pipe (follow building codes in your area) to connect the round exhaust on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. 8. Slide the inner duct cover up 2 inches before sliding the entire duct cover onto the hood. Refer to Figure 16. 9. Adjust the height of the inner duct cover to the inner duct cover-mounting bracket {J}. Secure the inner duct cover with two (1/8” x 3/8”) screws (provided). 10. Fasten outer duct cover to outer duct cover- mounting bracket {K} with two (1/8” x 3/8”) screws (provided) as shown in Figure 17. Accessories 11. Drop oil tunnel into recess support near rear of hood. Refer to Figure 18. 12. Install baffle filters and stainless spacer(s). Refer to Measurements and Diagrams on page 22 for baffle filter and stainless spacer placement. Angle baffle filter toward back of hood . Push baffle filter up until almost level . Slide forward into recess behind the front of hood . Lower baffle filter . Slide back until it fits into resting position . Refer to Figure 19. 13. Repeat step 12 to install all baffle filters and stainless spacer(s). Figure 15 Figure 16 Figure 17 Figure 18 11 Final Assembly Final Assembly Figure 19 14. Turn power ON in control panel. Check all light and fan operation. 15. Make sure to leave this manual for the homeowner. 12 OPERATION INSTRUCTIONS This KOBE hood is equipped with six electronic controls, two powerful centrifugal squirrel cages with stainless steel oil tunnel, stainless steel baffle filters and spacer(s), and bright 12volt 20-watt halogen lights (2 for 30” & 36” and 3 for 42” & 48”). The six electronic buttons control the Light, Speed (QuietMode™, Low, Medium & High) and Power (On/Off). The Power Control offers a 10-second delay startup, 3-minute delay shutoff or immediate shutoff. The Light Control operates independently from the Power Control and is not affected by the delay startup or shutoff. (Fig. 20) Figure 20 Q Light control Speed control Power control Turning Fan ON: Always turn fans on before cooking to establish air flow and allow fans to run for a few minutes after cooking for cleaner air in the kitchen. The Power Control (On/Off) button must be pressed before a Speed Control button can be activated. -Press the Power Control (On/Off) button once. The four LED lights above the Speed Controls will flash, if a Speed Control button is not pressed within 10 seconds, power will be automatically released. Note: The light setting will not be affected by the Power Control (On/Off) button. -Press a Speed Control butt...
Эта инструкция также подходит к моделям:Вентиляторы - CH7642SQB (1.34 mb)
Вентиляторы - CH7648SQB (1.34 mb)
Вентиляторы - CH7630SQB (1.34 mb)