Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
6 Ductwork Installation Ductwork Installation 8. Use 8” round steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 5. Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 9. Connect electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect wires according to their colors (i.e. black to black, white to white, and green to green). See Figure 6. - Store wires in the wiring box. Figure 5 Figure 6 Final Assembly CAUTION: Install heating lamps last. 10. Drop oil tunnel into recess support near rear of hood. Refer to Figure 7. 11. Install baffle filters and stainless spacer(s). Refer to Measurements and Diagrams on page 21 for baffle filter and stainless spacer placement. Angle baffle filter toward back of hood . Push baffle filter up until almost level . Slide forward into recess behind the front of hood . Lower baffle filter . Slide back until it fits into resting position . Refer to Figure 8. 12. Repeat for all baffle filters and spacers. 13. Install heating lamps (not included), 120 Volts 175 Watts max. each. Figure 7 7 14. Turn power ON in control panel. Check all lights and fan operation. 15. Make sure to leave this manual for the homeowner Figure 8 8 WALL MOUNT INSTALLATION ***Follow these installations only if installing with an optional duct cover: Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 9. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long run as possible. This may reduce the performance of the hood. • Use duct tape to seal the joints between pipe sections. • If necessary, prepare back wall frame with cross framing lumber for secure installation. • Using references in Table 2 on page 4 and Measurements and Diagrams on pages 19-20, decide the level of the lumber. Refer to Figure 10. Figure 9 Figure 10 Hood Preparation Before Installation • Temporarily wire the hood to test for proper operation before installing. • Important: Peel protective film off the hood and the duct cover (if any). • Attach ducting transition to hood exhaust with ten (3/16” x 3/8”) screws (included). Refer to Figure 11. • If necessary, attach two rubber stands (included) with adhesive tape (included) to the back corners of the hood. • Use eight (3/16” x 3/8”) screws (included) to attach the two hood-mounting brackets (included) to the back of the hood. Refer to Figure 12. Figure 11 Hood Installation CAUTION: If moving the cooking range to install the hood is necessary, turn off the power on an electric range at the main electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE. Figure 12 1. Using references in Table 2 on page 4 and Measurements and Diagrams on pages 19-20, 9 mark the leveling point of the hood. Position two mounting screws (not included) on the wall, leaving 1/8” away from the wall. Refer to Figure 13 2. Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. 3. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure installation, use as many mounting holes as needed to secure from the inside of hood (screws not included). CAUTION: MAKE SURE HOOD IS SECURE BEFORE RELEASING. WALL Figure 13 Wiring to Power Supply SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY QUALIFIED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES. BEFORE CONNECTING WIRES, SWITCH POWER OFF AT SERVICE PANEL AND LOCK SERVICE PANEL TO PREVENT POWER FROM BEING SWITCHED ON ACCIDENTALLY. 4. Connect the electrical wires. -Connect three wires (black, white and green) to house wires and cap with wire connectors. Connect according to color: black to black, white to white, and green to green as shown in Figure 14. - Store wires in the wiring box. Figure 14 10 Duct Cover Installation Duct Cover Installation 5. Use 8” round steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer Figure 15. Slide the duct cover onto the hood. 6. Use 3/16” x 3/8” screws (included) to attach duct cover to hood. Figure 15 Final Assembly CAUTION: Install heating lamps last. 7. Drop oil tunnel into recess support near rear of hood. Refer to...
Эта инструкция также подходит к моделям:Вентиляторы - CH0042SQB (2.03 mb)
Вентиляторы - CH0048SQB (2.03 mb)